Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

Starting first chair

Posts

Starting first chair

#1

Starting first chair

Joseph Mulherin, Sr.

I bought some MDF and made the forms for the rockers and back braces.

Cut the boards to 12? width, glued then together, glued and cut the patterns

onto them using my 11" Shopsmith bandsaw; then screwed some 1" angle iron pieces to the middle of the forms so the lams, when cut and glued up, will stay inline when they are squeezed into the forms. Today I glued up the chair patterns I received from Hal Taylor to some 1/2" plywood, then cut the patterns out on the bandsaw. Only lost one blade in all the cutting...my 1/2" one so will have to buy another from Shopsmith(72"s).

Am making the chairs using ALDER. It is almost as hard as OAK, but less expensive, and will stain nicely for the family's decors. Am planning on making several chairs for family members over this next year... 4 large, 3 medium, 2 small, and also have the plans for child's chairs which I will be making about 4 of them for my grandkids and greatgrandkids.

You can see the chairs at www.rockingchairuniversity.com; and also use www.rpckingchairplans.com to purchase the plans from Hal Taylor directly.

If and when I discover how to use those damn cameras I shall send pics every so often as I progress.

Re: Starting first chair

#2

Re: Starting first chair

Joseph Mulherin, Sr.

Started cutting the lams for the rockers and back braces on my table saw to 3/16"thk x 48" length. Need 4 per back brace, and 11 per rocker. Will glue up many braces this week and try to get the rockers done also. Each chair has seven braces in the back...outside is the Alder, inside is two lams of poplar or ash.

Design will be cut onto them later. Will but some 5.5" Alder from HD, glue the together to get my 1 1/2" thickness needed for the chairs lags and arms and seats. Am going to be using Charles Neil's scooping out the seat method...you can watch him on You Tube at "in the workshop" ....typed in when you connect.

Then power sand to get the finish sculptures.

To see Hal Taylor's videos...go to www.Rockingchairuniversity.com

Re: Starting first chair

#3

Re: Starting first chair

Joseph Mulherin, Sr.

correction...it is 3/32" thk on the lams....not 3/16".

Re: Starting first chair

#4

Re: Starting first chair

Joseph Mulherin Sr.

Yesterday I cut the lams on the table saw...both the alder and the poplar.

Today I glued up the lams...1 alder, 2 poplars , and 1 alder ; four lams per, used Titebond original glue,

installed them in the forms, squeezed them down using my pipe clamps and quick clamps on the ends, let setup for about 3hrs each. Removed them and scrapped off the squeeze out glue getting ready to run them by my disc sander on the Shopsmith. Need 7 back braces per chair.

The poplar is being used to give the braces some sprininess...the braces are not glued into the seat and headrests, rather are installed using wax in the holes to allow movement...the braces move back about 1.5 to 2" when you are seated in the chair and move a little sideways when you shift a little .

You can see the chair by going to YouTube and viewing some videos by Hal Taylor chair.

Re: Starting first chair

#5

Re: Starting first chair

Joseph Mulherin Sr.

Foloow up: you can go to www.hubyuk.128.blogspot.com...look for Building the Hal Taylor Rocking chair.

This guy built the chair and took some very good pictures of his work and the finishes. He built one for himself and another smaller one for his wife.

Re: Starting first chair

#6

Re: Starting first chair

Joseph Mulherin Sr.

Blogspot does not work...sorry. Use the Building the Hal Taylor Rocking Chair and up will come the guys pictures and blog of how he built the chairs.

Re: Starting first chair

#7

Re: Starting first chair

Joseph Mulherin Sr.

Glued up all of the back braces(8) and installed them in the forms, let sit for 3hrs

for each two braces being formed at a time...came out fine. Tonight glued up the last of them and will start squeeze out glue clean up, then run them thru the table saw to get the same width measurement. Can cut the ends of each brace which goes into the seat, but the headrest ends will have to wait until I get the headrest made and held in place to measure each brace before cutting the ends on them. Next project is to make the seat which will be scooped out using Charles Neil's method of using the dado blade...like I did on those other two chairs earlier this year.