Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Compare cordless drills on the numbers that matter

Evening out spray?

Posts

Evening out spray?

#1

JL

Evening out spray?

JL

I sprayed a project yesterday using a CAB lacquer. The sides were coated nicely (maple plywood). The top (reclaimed red oak) is a bit of a problem. The spray didn't lay down a very even coat - it is a bit "pebbled". Part of that may be due to the oak - as the ash and the maple look and feel okay.

So - I'm going to head over there later today to try and correct the problem. Any suggestions?? I was thinking about wet sanding or padding the surface to try and even it out.

Re: Evening out spray?

#2

Moses Yoder

Re: Evening out spray?

Moses Yoder

I would have to see it to really analyze why it didn't work right. Maybe not atomizing correctly or not a thick enough coat to flow out. I would mask off the bottom portion and lightly sand and respray the top.

Re: Evening out spray?

#3

adding a detail

Bill Tindall

It is getting to be hot summer. When it is warm to hot, a retarder is desirable. If the lacquer dries too quick it will not flow out properly and you get "orange peel".

Re: Evening out spray?

#4

Re: Evening out spray?

Dave Paine

You mention reclaimed red oak. The wood may be the problem, as you thought.

Red oak is very porous, being reclaimed may be even more so. It is likely the wood absorbed the spray in some areas where the end grain is proud. These areas would look like they were not sprayed.

I have experienced this in the past, although mine was likely brushed on at the time.

If you are lucky, the problem areas should now be sealed. As you stated, wet sanding the red oak and then try again - perhaps twice.

Good luck. This reminds me why I try to avoid using red oak.

Re: Evening out spray?

#5

oak could be contaminated by wax or oil?

Dick Coers

Maybe the oak was exposed to something that the lacquer doesn't like and that is effecting the bond. Silicon is the usual big suspect. Where did the oak come from? Pictures of the problem would help.

Re: Evening out spray?

#6

JL

The oak was reclaimed oak.

JL

It was formerly on the exterior of some shopping center as trim.

It was about 6/4 when I started. I planed it down considerably (almost 3/8") on both sides so it was just over 4/4. I stained it (brush on then wipe) and let it dry for a couple of days. When I sprayed it yesterday, some of the stain "oozed" out. So I suspecting that the oak was responsible.

Re: Evening out spray?

#7

Bleeding Oak

Mark Mandell - Gone Round In New Jersey

Is part of the reason I don't work the stuff very often.

Couple of suggestions: Since oak is famous for bleeding oil stains. . .

1. Use dye stain (NGR or water) rather than pigmented oil; no bleeding.

2. If oil's the only option, allow to dry 48 hours, then mist on (hand spray bottle) a coat of naptha; it will tend to pull the still-wet oil out of the pore pits and dry it.

3. Seal the stain in with a spitcoat of dewaxed shellac which can also be tinted with TransTints to adjust the color and tone. It will also give you more visual depth to the final finish.

4. When the shellac's dry, apply your top coating.

Re: Evening out spray?

#8

Ditto

Mark Mandell - Gone Round In New Jersey

Orange peel (pebble grain) on lacquer indicates interference with the tail solvents that allow the coating to level out. Heat (ambient or direct sun/IR) will do this as well as over thinning with high vapor pressure solvent that will flash off too quickly.

Remedy: Sand the surface level, add a proper retarder to the product, respray in a cooler location out of direct sunlight, double hit the application with the second hit at 90° to the first.

Re: Evening out spray?

#9

JL

Problem "solved"

JL

My HVLP sprayer was possibly putting out too much material. I probably should have thinned it and added a little retarder.

I ended up sanding the high spots off a little and then "padding" it with lacquer thinner and some muslin. This leveled it off reasonably and left an okay finish.

Next time - thinner with retarder - especially if I can find some retarder at an inexpensive price.

Re: Evening out spray?

#10

Sprayer?

Mark Mandell - Gone Round In New Jersey

J,

If you're using a turbine-driven HVLP to spray solvent finishes, you'll have continuing orange peel issues because of the heated air from the turbine; they work much better with waterborne finishes where the solvent doesn't get flashed off before the finish gets to the surface. Spraying solvent lacquer and shellac should really be done with a conversion gun and regular compressor to get optimal results.

Re: Evening out spray?

#11

you won't.......

Bill Tindall

find an inexpensive retarder, unless you know a chemist. The retarder will be something like butyl acetate and/or a high boiling ketone.....all expensive solvents compared to acetone and toluene.

Re: Evening out spray?

#13

Moses Yoder

Re: Thinning

Moses Yoder

I am not a spraying expert by a long shot. I have worked with some. What I know about spraying wouldn't fill one page. You say you were spraying too much material (possibly) and then say you need to thin it. Wouldn't this mean it would spray more material, if the finish was thinner?

Re: Evening out spray?

#14

JL

Re: Thinning

JL

As I understand it, think of "oatmeal" versus "flour". You get finer atomization of the finish if it is thinner. More solvent to "flash off" as opposed to more finish.