Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

coloring epoxy

Posts

coloring epoxy

#1

coloring epoxy

Lester Gillett

I am making a tv cabinet out of white oak. The boards i am useing for the top has some checks and

splits. Can you color epoxy with trant tins to match the wood color? The checks and splits will not

hurt the wood but would like to fill them in. IF not what can i use to fill them in and color the product ?

Lester

Re: coloring epoxy

#2

Re: coloring epoxy

Dave Paine

I have not tried Trans tint in epoxy, but this may not mix well due to the water base.

Most people use pigments or fine saw dust. I have tried the latter since I do not have pigments laying around. Easy to mix in with the epoxy.

If you go with the saw dust, I recommend very fine particles, from e.g., 200 - 300 or higher grit.

Re: coloring epoxy

#3

Sure

Mark Mandell - Gone Round In New Jersey

Lester,

I use TransTint [dye concentrate - in alcohol] to color epoxy all the time, sometimes in addition to wood flour or other additives, for filling. Using the dye (a drop or 2 is plenty) the epoxy will remain transparent, as opposed to using pigments or thickeners like wood flour.

Since you have open pore wood, you should seal the surrounding surfaces with something like shellac to prevent absorption of the tinted epoxy outside of the cracks. If your checks go through the board, you'll need to seal the opposite side and any exposed ends. While others may use masking tape for this, I find that it often leaks. Instead, I apply a wet coat of a wax emulsion like AnchorSeal and then immediately put a piece of Saran or other plastic wrap over the wet wax; makes a good seal if you support it by putting the workpiece on a flat surface. Attached is an example on Walnut. In this case, I wanted to accentuate the crotch crack that had bark inclusion, so I tinted with a medium brown

Re: coloring epoxy

#4

Re: coloring epoxy

Ralph Lipeles

I use powdered tints quite often with epoxies to better match the wood that I am repairing. Use small amounts of the powder and mix very thoroughly. Add more stain as may be required.

Re: coloring epoxy

#5

Re: coloring epoxy

Lester Gillett

Thanks Mark and Ralph for the information. Mark the walnut crack is about like what i have to seal.

Will go over to Wood Craft and git some of the trant tins and epoxy and fill the splits. I was thinking

about putting super glue in to hold the fibers be for sealing it. Would this be as good for sealing the

area around the splits ?

Lester

Re: coloring epoxy

#6

Splits

Mark Mandell - Gone Round In New Jersey

Lester,

No, the CA ["Super Glue"] will tend to soak in and then mess up your finishing routine. Shellac, however, will sand off easily. You can also use paste wax, like Johnson's, but you have to be careful not to get any inside the cracks as the epoxy won't stick to it.

For large cracks like my walnut piece, you should consider at least one butterfly inlay to stabilize the gap as seasonal wood movement will tend to open or close the gap and loosen the cured epoxy fill.

PS: You don't need to "prime" the inside surfaces of the cracks; the epoxy will get a better grip on the fibers if you don't.

Re: coloring epoxy

#7

Re: Splits

Lester Gillett

Mark

Thanks Mark, What type of epoxy did you use and how hard is it to level out ? My splits are not to

wide and i have a few knots that need filling that i want to do. I have a belt sander but not to handy

with it. I do have a club member that has a 38" wide drum sander i may have him run it threw. Will

take a few pictures to show what it looks like later.

Lester

Re: coloring epoxy

#8

Re: Splits

Dave Paine

My experience with sanding epoxy is to be careful about heat.

You mention drum sanding. A drum sander can generate a lot of heat, which may cause the epoxy to partially melt and if this happens the wrap will be ruined. Very light passes are recommended, feeling the epoxy to check it is not getting too hot.

I have not had problems sanding epoxy, but it does create a lot of dust. I also recommend having dust collection, even if it is only a buddy holding a shop vac close to the sander.

Re: coloring epoxy

#9

Re: Splits

john lucas

Lester I have used a lot of things to color epoxy. Trans tint and India inks work well as do oil and acrylic paints that come in tubes. Always always always run a test first. Every once in a while the stuff I mix into the epoxy will change it's properties and it either won't harden or will be too soft or foam up and create holes etc. Test first, please. I find the trick for doing what your doing is to mix the epoxy so it's translucent. Then it picks up some of the color of the wood. You'll never get it to match so it won't show so I usually shoot for darker. When filling defects in knots I can almost get it to disappear but cracks in good wood is just about impossible.

for leveling the epoxy will not be the same hardness as the wood. could be softer or harder depending on the epoxy. For that reason I prefer to use a more mechanical leveling tool such as files or cabinet scrapers to get it really close to flush. then switch to sandpaper.

Re: coloring epoxy

#10

Dave's Comment Plus

Mark Mandell - Gone Round In New Jersey

I use System 3 or West resin with their "fast" or "medium" hardener. Mixing can be a bit fussy. I bought a small $15 digital gram scale which has helped quite a bit. System 3 is mixed 100 parts resin to 44 parts hardener by weight. This is more precise that other resins, as you can make very precise mixes that give maximum strength, especially in small batches.

You must let the epoxy cure well before sanding it; I wait 18 to 24 hours. I find that 80 in an RO does quite well to level the filler (also takes off the shellac sealer), then sand your piece up through the grits as you normally would.

Re: coloring epoxy

#11

Be wary of splits

Bill Tindall

My experience with splits is that they are unstable. they come and go and eventually crack the finish and look line cracks and splits.

Re: coloring epoxy

#12

I recently found one that works with Transtint... *LINK*

John in NM

The dye does thin it a bit more than I expected, but then I'm going for really dark to match walnut, so I tend to use more dye than you likely will.

I used to see this stuff in hardware stores all the time, now it seems to be a bit scarce. Getting hard even to find a hardware store around here.


PC-11

Re: coloring epoxy

#13

What kind of epoxy?

John in NM

I tried it in 5 minute and never got it to mix, at least not like it mixes in others. I was using this really fancy stuff at work that it would mix with readily, and finally found a place that sells the retail equivalent (at least to my non-chemist eye).

Re: coloring epoxy

#14

Re: What kind of epoxy?

Mark Mandell - Gone Round In New Jersey

TransTints are alcohol-based dye concentrates. They should mix with any epoxy resin. I never use the 5-minute stuff as it seems weak. I use System Three General Resin + one of two of their hardeners. A single drop of the dye concentrate is plenty to color a full ounce of mixed resin. Mix resin and hardener first, then add the TransTint (Not TransFast which is a waterbased dye that won't mix).

You do, however, have to be careful when adding alcohol to epoxy. Reason is that epoxy is a thermoset and will get quite warm during the reaction; hot enough, in fact, to boil the alcohol which will result in epoxy foam bubbling out of your joint. I learned this the hard way because someone on a website said it was ok to add up to 20% alcohol to thin the resin. Bad advice according to the manufacturer's tech rep when I called.

Mixing epoxy should be done carefully; that's why I bought a digital gram scale. Since then, I mix by weight and all my pours have come out perfectly.

Re: coloring epoxy

#15

PS

Mark Mandell - Gone Round In New Jersey

Saw you post on PC-11 paste. I highly recommend making your own paste using wood flour with the the fines that stick to the filter in your DC or vac. Run them through a fine sieve and the add what you need to mixed resin to bulk up the mix to a working paste. You can also add some dye to shift the color.

Here's an example of regular epoxy with wood flour as a filler in walnut

Here is an example of tinted epoxy using TransTint and just a little walnut dust

Re: coloring epoxy

#16

Boiling...

John in NM

We used to have that problem with West system if it was a huge void being filled, it would start to smoke and boil a bit. Often we got around that by using some filler wood to simulate a knot or something similar - I never got the hang of that look, but some of the guys were very good at it.

Lately I've been making a lot of parts out of urethane resin, and that stuff gets hot - it also picks up moisture readily, so I've had a couple pours do the boiling routine. You end up with about 10x the volume due to the moisture boiling, and end up with a huge mess where ever you were working (hopefully not the kitchen counter :D ). Another time I tried a new colorant, that was glycol based and worked well with regular epoxy, but not with the urethane - same result, a big foamy mess.

Re: coloring epoxy

#17

Urethane

Mark Mandell - Gone Round In New Jersey

needs dry, non-reactive pigments, I think. I tried the Polyall 2000 2-part urethane and didn't have much success with the stuff.

Re: coloring epoxy

#18

Re: Urethane

John in NM

I've had good luck with pre-tinted products - fortunately I'm making black parts so pre-tinted is available. In this case I'm using it for casting rather than filling, not sure it would work well as a filler - stuff goes off fast, 3-5 minutes. Makes a fantastic casting resin though.

The first stuff I tried did require a pigment, but the vendor supplied a paste pigment that worked well - no idea what the fluid in the paste was, something that boiled higher than the cure temp of the resin. Before the vendor started carrying black resin, I was going to try some lamp black powder. The trouble with dry pigments is that they can introduce additional air to the mix, but since I'm pulling a vacuum before pouring that was less of a concern.

I would guess that dry pigments would cause fewer curing problems, being basically inert. With paste or fluid pigments, I try to keep it under 5% by weight.

Re: coloring epoxy

#19

Re: coloring epoxy

Tony - Memphis

I have used ground pastels and acryclic paint. Both worked well, but I liked the pastels better. I buy them at Hobby Lobby (40% off coupon in paper or online) and rub them on sandpaper to make them into dust. For your scale, you might need a better method than sandpaper. I've read that some peopele use RIT dye powder with epoxy. I did some samples before I proceeded. My project was much smaller than your - filling in gaps in a laser cut pen kit. Worked great though. The epoxy took longer to cure an felt a little gummy for a while, but it did cure nice and hard. I just used 5 minute epoxy from Lowes.

There was an article in FWW on making epoxy inlay that might be a good reference.

Tony

Re: coloring epoxy

#20

Re: coloring epoxy

Lester Gillett

Here is a few photos of the split i need to fill. Also one that show the cabinet i am working on.

Re: coloring epoxy

#21

Re: coloring epoxy

Lester Gillett




Here are the photos i for got to add to the post.

Lester

Re: coloring epoxy

#22

Re: coloring epoxy

Ray - Middletown, in

Using West Systems epoxy, I use the Microlight 410 filler to get the consistency I need. Then I add Artist Oil paint to get the color right. Pour it out on a flat surface and using a pallet knife squeegee it out to a thin layer, this does two things. It keeps the epoxy in a smaller volume which lengthens the working time some, and it helps to remove any air bubbles, particularly if you mix it to a peanut butter thickness. Put a thin layer of colorless epoxy on the sides of the split to prevent any color bleed through (regardless of coloring method used), then apply the colored epoxy. Using the 410 filler helps to make the cured product a little less brittle and works more like a piece of wood.

Ray