Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

RE: Thanks for the advice.

Posts

RE: Thanks for the advice.

#1

RE: Thanks for the advice.

David Frame

I agree with everyone about the cyanoacrylate glue being brittle. I did not know about the moisture in and around the glue that made it hard. Now I know why it last only several months a plastic bottle. However, many of you stated that the dried glue would last about 10 years in a project. I have to disagree with that statement.

Back in 1996, I built a total of 85 humidors. 60 of them went to Emeril's Restaurant in New Orleans and around the country to his other establishments. The rest were sold at a cigar shop in Metairie and New Orleans, LA. New Orleans is where I was born and lived there most of my life. So I know Emeril personally. He bought the humidors and we, a friend I know since diapers, supplied the contraband cigars. His restaurants were cigar friendly after 9:30 pm back then about 17 years ago until smoking was outlawed sometime in 2009 under the Tobacco Act by President Obama. And He's a smoker.

Not all of the humidors looked the same. I only built 9 of the one in Shop Shots. Every box was a different wood in this style of humidor. 2 were domestics and 7 were exotics. Not one of the Satellite Glue joints failed. That is 17 years ago and my work is guaranteed for life, with the exception of misuse and abuse. I also state in writing that my boxes are not drop proof.

There is one I built in 1997 for a friend to help me finish my home. It can be seen here in Shop Shots in Shots #101 to 200 entitled, "CIGARS NEVER HAD IT SO GOOD" (David Frame, Jr.) 9/2/00. The reason I posted it in 2000 was is because I wasn't aware WoodCentral existed at the time. That one is 16 years old for the one in Shop Shots and looks as good as the day I built it.

After I posted it, I was also accused of plagerism. This person said it looked similar to one he had seen in a magazine with the exception of the inside of the humidor. The only magazine I read and still do is Fine Woodworking. If you find it in FWW, I'm guilty. But you won't find there.

Most of the woods I use for humidors are solid exotics. All of the solid woods are sealed in a 4 to 1 cut of Shellac so that the solid wood won't move very much. It is also one of the reasons I have been using instant glues. A quick wipe down with laquer thinner on the cut beveled edge, give a minute or two for the thinner to evaporate and then glue and assemble it. The one in here Shop Shots is one of two I made in domestic woods. They were the exception to the rule. The exotic woods I've been using have some oils in them and these exotics don't move very much. I bring the wood in my home to acclimate. Keep all my exotic and figured woods in a spare bedroom that I know I'm going to be using soon. There is a professional dehumidifier on low in that bedroom that a friend gave to me after his business failed.

The person that helped me with my home saw some figured maple I had and wanted a humidor made with it. The other domestic wood I built a humidor with was booked matched crotch grain black walnut that came from a tree a friend and I cut in Converse, LA. All of these humidors have yet to come back to me for any kind of repair.

However, now that I know more about cyanoacrylate glue, I'll be looking for a new glue to use. I think I'll start with the Starbond Brand. If that doesn't work, I'll try the 5 minute epoxy. It just so long to cure.

By the way, why do so many people call a beveled cut a miter? Just a thought.

Thanks for everyones expert opinions about this instant glue. I've learned quite a bit overnight, than in the 39 years I've been woodworking.

Thank you for your time and patience.

Sincerely,

David Frame

dframe01@hotmail.com

Re: RE: Thanks for the advice.

#2

Re: RE: Thanks for the advice.

Dave Paine

Commenting on your statement

"By the way, why do so many people call a beveled cut a miter? Just a thought. "

I have always considered a cut made with the blade at right angles and the cut line at an angle other than 90 deg to the work to be a miter cut.

A cut made with the blade tilted at an angle other than 90 deg to be a bevel cut. If the cut line is other than 90 deg, this is a compound cut (miter and bevel).

Miter cuts are common for e.g. picture frames where the depth is less than blade height.

If the depth is greater than blade height, e.g., sides of boxes, then you are into a bevel cut.

Compound cuts are seen in e.g., crown molding. Can be very frustrating to get this one to match.

Re: RE: Thanks for the advice.

#3

Re: RE: Thanks for the advice.

David Frame

Dear Mr Paine,

A coumpound beveled cut has 2 Angles on it. You said it your self," Coumpound cuts are seen in e.g., Crown Molding can be very frustrating to cut to get this one to match." That's not the only place you see them. One of my first projects was a lamp with 8 angles sides. When the top and the bottom were put together, it liiked like an hour glass. And yes, Each top and bottom had 8 pieces at 22.5 degrees. Of the 16 pieces that had been cut, each piece had 2 cuts on them. All of them had cuts with and against the grain.

I consider a miter joint a thin piece of material lying flat on a table saw in a jig or on a miter saw, cut to a 45 degree angle or less if the work turns out to be a triangle, square, pentagon, hexagon, or octagon or more. A bevel may be cut flat on a table saw with or across the grain of the material.

If you look in Shop Shots #101 to 200, Date 9/02/00, the humidor I built, Is it a miter or a bevel? Keep in mind that the top was cut from the box while it was still whole. And I used a shootong board to cut them.

David Frame

dframe01@hotmail.com

Re: RE: Thanks for the advice.

#4

Re: RE: Thanks for the advice.

David Frame

David Frame

Dear Mr Paine,

A coumpound beveled cut has 2 Angles on it. You said it your self," Coumpound cuts are seen in e.g., Crown Molding can be very frustrating to cut to get this one to match." That's not the only place you see them. One of my first projects was a lamp with 8 angles sides. When the top and the bottom were put together, it liiked like an hour glass. And yes, Each top and bottom had 8 pieces at 22.5 degrees. Of the 16 pieces that had been cut, each piece had 2 cuts on them. All of them had cuts with and against the grain.

I consider a miter joint a thin piece of material lying flat on a table saw in a jig or on a miter saw, cut to a 45 degree angle or less if the work turns out to be a triangle, square, pentagon, hexagon, or octagon or more. A bevel may be cut flat on a table saw with or across the grain of the material.

If you look in Shop Shots #101 to 200, Date 9/02/00, the humidor I built, Is it a miter or a bevel? Keep in mind that the top was cut from the box while it was still whole. And I used a shootong board to cut them.

David Frame

dframe01@hotmail.com