Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

Cheap edge bander *LINK*

Posts

Cheap edge bander *LINK*

#1

Cheap edge bander *LINK*

Henry Higginbotham

Anyone have experience with cheap, manual hot-air edge banders like the Freud shown here?

A couple of friends and I won a large (to us) quantity of edge banding in an auction, and are now wondering what we'll do with it, especially the thin stuff. A portable unit like this could be stowed away during the 99% of the time it's not being used. But . . . do they work well enough to bother with? Can 2mm or 3mm banding be used? Plastics? The Freud site doesn't seem to be much help.


http://www.freudtools.com/p-270-eb100-edge-bander.aspx

Re: Cheap edge bander *LINK*

#2

Re: Cheap edge bander

Keith Newton

I have one of those out in the shop somewhere that I bought for a project about 15 years ago. I have not used it except for that one job, and would welcome an offer for it. I suppose it can do the job, if someone is willing to learn its exentricities, and practice pleanty of quality control. But I was using some low skilled pick-up help that didn't give a rat's care, nor willing to learn or exert the energy, so it failed to meet my standard one month product warranty.

Re: Cheap edge bander *LINK*

#3

Re: Cheap edge bander

Mark Nowicki

I still have the heat gun, and it is a good one. The rest of the assembly is at a bottom of some landfill.

My problems were an inability to maintain a consistent feed rate and pressure. The glue runoff would collect on the roller and globs would push the banding out of alignment.

I suppose a contraption consisting of feather boards and power feeders could make it work but I was not willing to make the effort.

You know the saying about the futility of polishing a turd.

Mark

Re: Cheap edge bander *LINK*

#4

Re: Cheap edge bander

Bob Lang

Pre-glued edge banding seems so simple in concept, but any method of applying it requires practice, and a sensitivity to what is going on with the glue, the substrate and the banding. There is more art and skill to it than you would expect.

The device shown is a step up from sneaking the iron out of the laundry room, but you have to be aware of the sweet spot where the glue is melted enough to stick, and press and move with just the right force and speed to make the banding stick. That will change with the type of banding, substrate, temperature, phase of the moon and sunspot activity.

There's a reason why automatic edge banding machines that cost tens of thousands of dollars are used in professional shops, and in that situation, they are a bargain. The little guy can't expect the same efficiency or results from tools like this. Lower your expectations, practice some and it isn't a bad tool.

Bob Lang

Re: Cheap edge bander *LINK*

#5

Re: Cheap edge bander

Henry Higginbotham

I've used the iron-on banding several times with no problems, but I (mistakenly?) assumed the Freud and similar machines used a separate dispenser of glue pellets. None of the edge banding I acquired is pre-glued.

Re: Cheap edge bander *LINK*

#6

Re: Cheap edge bander

Bob Lang

Nope, it's just a method of heating and pressing the pre-glued stuff. Sounds like your best bet is to use contact cement with what you have.

Bob

Re: Cheap edge bander *LINK*

#7

Thanks, everyone.  Sounds like . . .

Henry Higginbotham

I may just use the 2-3mm stuff with PVA glue and clamps, and the thin stuff can be kindling or shim material, or I may try Craigslist. I don't use that much of it, anyway.

Re: Cheap edge bander *LINK*

#8

Re: Thanks, everyone.  Sounds like . . .

Dave Bair, Eaton Rapids, MI

A recent PopWood or FWW article used banding to make unique lamp shades.