Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

Accuspray Model 10 HVLP Gun: Tip/Nozzle/Air Cap Re

Posts

Accuspray Model 10 HVLP Gun: Tip/Nozzle/Air Cap Re

#1

Accuspray Model 10 HVLP Gun: Tip/Nozzle/Air Cap Re

Phil

I've had an Accuspray HVLP setup for a dozen years or so, but since its for hobby use, it does not have all that many miles on it. Does the delrin tip (or nozzle or air cap) need to be replaced after so many hours of use? I've done zero maintenance on the gun, and I see that they sell maintenance kits with replacement o-rings, etc. Is there any preventative maintenance I should be doing? I am planning on shooting General Finishes Enduro-Var. GF suggest an .043 to .051 tip/nozzle and a #9 air cap. I have the .043 tip, and I've always used a #9 cap, any advantage to switching to the .051 tip/nozzle with the #9 cap? Thanks

Re: Accuspray Model 10 HVLP Gun: Tip/Nozzle/Air Cap Re

#2

Re: Tip

Mark Mandell - Gone Round In New Jersey

Phil,

While I don't have your gun, there are several things that will apply notwithstanding.

The larger tip will pass more fluid. The more fluid of the same viscosity being mixed into the air stream, the more air will be needed to adequately atomize the finish to get an even spray pattern.

With the larger tip you'll likely have to increase your air mix, by increasing the pressure, which may cut down on your HVLP efficiency and give you more over-spray and more opportunity for for orange peel.

If you're doing large surface pieces like tables, cabinetry, and doors, the larger tip makes sense. OTTH, if you're spraying smaller items or pieces with smaller parts like boxes or chairs, the smaller tip will give you more control and save finish.

Hope this helps

Re: Accuspray Model 10 HVLP Gun: Tip/Nozzle/Air Cap Re

#3

Re: Tip

Phil

Mark: OK, makes sense. I might just pick up the larger nozzle/tip to see if there is any improvement in performance/finish. I have a cheat sheet for the air and fluid control settings, I'll fool around with some leftover finish and see what happens. Thanks Phil

Re: Accuspray Model 10 HVLP Gun: Tip/Nozzle/Air Cap Re

#4

Re: Fluid

Mark Mandell - Gone Round In New Jersey

Phil,

You can, of course, back off the fluid needle for control, but then that pretty much defeats the purpose of the larger tip.

BTW If you don't have a secondary mini-reg on your gun, I strongly suggest you get one. Gives you very precise control over the air flow right at the gun that a compressor regulator can't match.

Re: Accuspray Model 10 HVLP Gun: Tip/Nozzle/Air Cap Re

#5

Re: Fluid

Phil

I'm using an Accuspray model 23 turbine (I think its a 3 stage unit). No controls that I'm aware of on the unit (except the on/off switch), and only a single flow and single air control knob on the gun. I'm not sure where this secondary regulator would fit in (unless you need something like that if you are using a compressor instead of a turbine unit)? Here is pic. of current model of my unit (looks the same as the one I bought years ago):


img

Re: Accuspray Model 10 HVLP Gun: Tip/Nozzle/Air Cap Re

#6

Ooops, My Bad

Mark Mandell - Gone Round In New Jersey

Didn't remember Accuspray made a turbine set, so I assumed you were working a conversion gun off a compressor. Sorry, forget the regulator advice; does not apply.