Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Fast and affordable laser cutting – so you can make the parts you can’t find anywhere else

best finish for black and white ebony

Posts

best finish for black and white ebony

#1

best finish for black and white ebony

raoul duke

I'm somewhat new to woodworking and decided to take on the project of making new foregrips for my ak-47. I'm using black and white ebony. I was wondering what the best finish would be? should i use polyurethane. or is there a better product?

Re: best finish for black and white ebony

#2

Ellis Walentine

Look into Tru-Oil

Ellis Walentine

You can get it from any gun accessory dealer or from Woodcraft Supply, one of our esteemed sponsors.

Ellis Walentine, Host

Re: best finish for black and white ebony

#3

Re: best finish for black and white ebony

John in NM

I use either Watco or Waterlox on my Hk grips and stocks.

I've tried Tru-oil once, it behaved a lot like either of the two above. It is probably the least yellow if that matters to you (as in how white is the white?).

On the whole Watco Danish oil tends to be the easiest to find and use, and doesn't gel up in the can the way Waterlox does.

Most oil finishes tend to yellow to some degree or another, if you want as colorless as possible look into water borne urethane or lacquer.

Re: best finish for black and white ebony

#4

Re: best finish for black and white ebony

Steve Schoene

Watco and Waterlox are entirely different kinds of finish, and are themselves both different from the Tru-Oil. Watco is a mixture of oil and varnish--not a large solids content, and if you apply it you MUST wipe off all the excess or you will have a really soft film on the surface. Waterlox is varnish, not a mix of oil and varnish. Yes, tung oil is one ingredient in the varnish, but it has been cooked with resins (phenolic and a bit of pine rosin) to chemically transform it into the varnish. You can build a film on the surface with varnish if you want. Tru-Oil is linseed oil, but linseed oil that has been industrially polymerized. The polymerization allows it to cure much harder than boiled linseed oil would if cured in air. It lets the Tru-Oil cure much faster than boiled linseed and makes the cured result hard enough that it can be allowed to build a bit of a film on the surface.

Note that ALL of the oil based varnish products will impart an amber tone to the white portion, some more than others, and some will yellow significantly over time. A diffent approach entirely is needed if you want to end up with white white.

I do have a question. What is the "white ebony" to which you refer?

Re: best finish for black and white ebony

#5

Yes, they are different...

John in NM

Any similarity implied has to do with the mode of use, cure times, and ease of use rather than chemistry. In this context I find them to all be fairly similar products compared to urethanes and lacquer. From the user's point of view I've found little difference between Watco and Tru-oil, though I've little doubt they are very different in composition.

I was wondering about the "white" ebony too, and then I realized that "black and white" likely refers to Macassar ebony. What confused me initially is that the handguard he refers to has upper and lower parts, so I imagined one black and one white :D

Re: best finish for black and white ebony

#6

David Barnett

Two different ebonies *LINK*

David Barnett

"I was wondering about the "white" ebony too, and then I realized that "black and white" likely refers to Macassar ebony."

Not necessarily.

Black and white ebony is Diospyros embryopteris, native to Laos.

Macassar ebony is Diospyros celebica, native to a broader section of Southeast Asia and the Indian Ocean.

B&W ebony has an altogether different appearance and greater contrast than Macassar.


Black and white ebony (Diospyros embryopteris)