Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

Installing Crown Mold

Posts

Installing Crown Mold

#1

Installing Crown Mold

Lynn Reedy

Greetings from Soddy Daisy Tenn.,

There is a standard crown mold sold at all the large box stores

that is 5/8 by 3 5/8. When using this mold, normally I measure

a certain distance down the wall for the bottom of the mold. If you

go by the flat spots on the back and place it in a jig, the measurment

is 3 inches. This is not working good this time. Does anyone know

what the measurement is down the wall to the bottom of the mold.

Thanks for the help...

Re: Installing Crown Mold

#2

Re: Installing Crown Mold

George Koch

It must not be your standard 38/52 degree crown. Place a short length in your miter box making sure it sits flat against the back and base and pencil mark the back, then measure from base to pencil mark.

Re: Installing Crown Mold

#3

Re: Installing Crown Mold

frank ashmore

put a square on it and measure it.

Re: Installing Crown Mold

#4

Re: Installing Crown Mold

Pat Evans

Greetings from Lewisville, NC. I hope the first two posts answered your question. I was surprised to see a message from Soddy Daisy. We're passing by very close on Friday. We're having lunch with a friend in Signal Mountain on our way to Birmingham. That's a really beautiful area.

Re: Installing Crown Mold

#5

Re: Installing Crown Mold

Guillaume Dery

You have 2 good answers. I jsut had to reply. Some of my inlaws are in Soddy Daisy (most of them in Chattanooga proper) and I am all the way up in Canada.

Small world indeed!

Re: Installing Crown Mold

#6

Re: Installing Crown Mold

J. Waters

I'm not sure what you are talking about, I have never done crown that way. Why would you need this measurement? I always cut to fit (cut on the angle in the miter box), a little more time, but I found it best.

maybe this is why I never understood cutting it flat, I wasn't taught to do it that way.

Re: Installing Crown Mold

#7

Re: Installing Crown Mold

NickinMass

Are you measuring down from the top corner of the wall to strike a control line for installation? You can run into serious problems if the corner seam wasn't finished uniformly. The trick I learned from Gary Katz (his website or one of the videos, I can't remember) is to make a plywood holder for the crown. First measure what the height and projection of the installed crown should be (on your miter saw fence or some other good 90 degree fence), then cut a holder from plywood that will hold the crown in that position against the wall (it will reference the wall and ceiling some inches away from the corner joint, so bulges and hollows won't interfere). It makes installation much, much easier and maintains the proper spring angle of your crown even if their are bulges and hollows in your wall.

Re: Installing Crown Mold

#8

Re: Installing Crown Mold

NickinMass

I rooted around and found this one that I made for installing the top piece of a two piece crown installation. The notch at the bottom is to allow for the already-installed first piece.


img

Re: Installing Crown Mold

#9

Re: Installing Crown Mold

Jason Waters

I'm glad I've never read any of the books on installing crown. I guess I have done well installing by eye so to speak (I do install blocks sometimes at each end to hold it the right height. I guess having a father and grandfather as contractors, I didn't have to read much, just watch.

On larger crown, I do install a nailing strip behind the crown agaisnt the ceiling. That way I can shoot nails wherever I want to pull in crown agaisnt one of those dips.

Re: Installing Crown Mold

#10

Re: Installing Crown Mold

Jim in N. Va

I'm dealing with a difficult ceiling right now, so any potential help is intriguing. However, I'm not quite sure how the holder is used or how it helps. I can see that it would be useful in marking out layout lines with a reference that avoids the corner. But how does it help during the install?

Looks like it is designed to hold in one hand while nailing with the other. Right? But, ultimately the crown need to get pushed back along the wall/ceiling doesn't it? Or, is the point of this device that it *doesn't* get pushed back and the crown would therefore "float" over the hollows? (And resulting gaps get heavily caulked.)

Thanks for posting the photo. Any additional instructions would be appreciated.

Jim