Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

motor bearnings

Posts

motor bearnings

#1

motor bearnings

Dan Long

Hi I have finally restored a newman600 24" planer it has a direct drive motor 5hp and when i turn it on it will make a low pitch sound I greased the bearnings which seemed to help but still semm way louder than normal. I haven't installed the blades yet but dont think it will make it better. I am looking to change the bearnings on this thing but can't seem to figure out how to get at them to make a change any help woud be great. Thanks Dan

Re: motor bearnings

#2

Re: motor bearnings

Charlie Lenz

A 5 hp motor should probably be run on 3 phase. As far as changeing bearings, I'm thinking that looking for advise on that in the Vintage Machinery website would be a better bet.

Re: motor bearnings

#3

First...

John in NM

Check the motor plate for the power requirements. An old direct drive 5 HP motor is, as Charlie says, quite likely to be 3 phase. If you plug it into 240 single phase, you will get a lot of noise and maybe some rotation, maybe not (depends on the load on the motor). Could be that is your problem rather than bearings.

Re: motor bearnings

#4

5 HP fine on 220

Bill Tindall

I have run a 5 HP planer on 220 single phase for 20 years and shoved thousands of bdft of lumber through it.

Re: motor bearnings

#5

Re: 5 HP fine on 220 ( Bill )

Charlie Lenz

Bill, your claim is probably correct, but here is a recent article that I was following on this subject. http://forums.finewoodworking.com/fine-woodworking-knots/power-tools-and-machinery/5hp-or-3hp-table-saw

Re: motor bearnings

#6

It's a fact

Bill Tindall

There is no "probably correct" about it. It is a fact. We ran an 18 inch Powermatic with a 5 HP motor 10 ga wiring from machine to box and used it to plane lumber orders of typically 200 bdft of hardwood lumber per order and up to 500 bdft on occasion, taking off 1/16" to 1/8" per pass. I would shove as much lumber through at a time as the plane was wide. Not at all uncommon to have most of the 18" planing. Never tripped a breaker or motor fuse. Never had a motor problem. Time to reach operating speed of the cutter-head was essentially instant. I still have the machine and use it for my hobby work but it only sees a few hundred bdft a year now.

Those folks on FWW Forum need to ask over here where there is actual experience. You might direct them this way.

Re: motor bearnings

#7

I took it to mean...

John in NM

A 5 hp motor on an old industrial machine is more likely to be 3 phase than single phase.

There is no reason a 5 hp shouldn't be single phase (I didn't read the fww article, no subscription), and like you, I would view the assertion that there is something "wrong" about large single phase motors with a lot of skepticism.

Three phase is however, more efficient for large motors. I suspect that's where the logic of such an argument would come from.

Re: motor bearnings

#8

and cost

Bill Tindall

One can pick up used 3 phase motors dirt cheap.

Re: motor bearnings

#9

Re: motor bearnings

Phil Smith

Newman Whitney is still in business. Suggest you give them a call and order a Manual. The cutter head and motor is an integrated unit. Manual will help to take apart.

Also post on the owwm.org site for help. You should contact Accurate Bearing for good price on bearings. Bearings for some of the industrial planers can be pricey n

Re: motor bearnings

#10

Re: motor bearnings

Dan Long

Thanks I downloaded the manual and will see if it will give me the info I need As far as the 3ph I am running three phase know off a 15 hp converter and the motor appears to run fine it just is makeing a lot of noise well see what hapens if all fails I will take it to a motor shop there are some real good ones by me hear and thanks to all who have replied for you comments.

Thanks Dan LOng