Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

newbie spraying question

Posts

newbie spraying question

#1

newbie spraying question

Jerry Gibbs

I want to spray clear finishes on wood, such as lacquer, varnish etc. I have a compressor with regulator. I also have an old, but good, spray gun of the high pressure type (and overspray). The container is on the bottom. I need practice, but in the end will not put much overspray in the atmosphere because of low usage.

My question is should I start practicing with what I have or should I buy a hvlp gun. I see a 2 gun kit at Harbor Freight for $50 plus shipping. Since I have learning to do, such as thinning and spray control, am I wasting my time with what I have? thanks.

Re: newbie spraying question

#2

Re: newbie spraying question

Larry Clinton At Frankfort, (Central) Indiana

I have both - a couple of Binks guns I picked up at auctions and some HF HVLP conversion guns. I spray a lot of Lacquer and some shellac. Actually my go to gun is the Binks, IMHO it gives a better finish overall and is somewhat easier to control. However my HVLP conversion guns are quite cheap so may be comparing apples to oranges. If I were you I would play with the gun I have. I use Qualalacq Lacquer in the spray version, but still thin the lacquer by 25 to 40% and spray a thin finish. Takes 3 or 4 coats to equal 2 coats of non-thinned lacquer but is far easier to control runs etc. and gives me the opportunity to inspect and smooth any area between coats. I have used cardboard boxes to set up, you can see the spray pattern easy and make your adjustments in gun and technique before spraying product. As far as I know the high pressure guns will do as good or better a job than the HVLP in every area of spraying. The HVLP does save some finish and has less "bounceback" - most of the time I use the HVLP it is only to spray inside of "dead end" areas like inside chests, boxes or deep shelves. The reason is that the lessened blowback makes it easier to see and more material gets into the corners.

Re: newbie spraying question

#3

how much pressure...

Jerry Gibbs

do you run the high pressure gun at? and thanks for the advice.

Re: newbie spraying question

#4

No!

Bill Tindall

Think about this for a moment. For decades stuff got sprayed with conventional guns. HVLP got introduced not to solve some problem with the result from conventinal but rather to meet a CA regulation.

HVLP is more picky about technique, so it is not the easiest place to learn. And, the benefit of lesser overspray is some, not huge. And finally the Harbor Freight gun is likely junk.

If you indeed have a quality conventional gun get thee a piece of cardboard and a cup full of water and spray away until the spraying motion is routine and the pattern is uniform.

I taught my daughter in a few minutes to spray simple pieces . She then sprayed her wainscoating with little effort. Something like a chair takes more experience.

The 3M PPS cups make life convenient and you can spray upside down and sideways.

Re: newbie spraying question

#5

I agree with everything Larry said

Bill Tindall

I have a very high quality conversion gun and I still use the DeVelbiss for most things.

Re: newbie spraying question

#6

Re: how much pressure...

Larry Clinton At Frankfort, (Central) Indiana

Set your pressure just high enough to get good atomization - I usually run about 35 - 40 lb with thinned lacquer. If your pressure is too low you will get "droplets" and not a full spray pattern. If you set it to high you get a cloud of mist with a lot of overspray. Pressure is dependent on a couple of things 1. The opening of the tip your using and 2, the thickness of the material your spraying. Start low - say 25 lb and work up until you get the spray pattern you want. Bill has a great idea -spraying water will let you practice on cardboard and learn without having to do much gun cleanout. Water should behave much like thinned lacquer - by the way when I thin my lacquer, I just fill my paint cup about 1/2 to 3/4 full then add thinner, the mix is not critical - just have to put more coats on if you get it real thin. You might want to get some lacquer retarder also. The retarder is a slow thinner that lets the lacquer flow more in hot weather, and also keeps the finish from blushing when the humidity is high. I usually don't add more than an ounce or so depending on the temp. and humidity. Again I don't measure it just pour a little in.

Re: newbie spraying question

#7

Re: how much pressure...

Barry Irby

I am no expert but I agree with most f what has been said. I would start at about 35 to 40 PSI, and I would learn with what I have.

Re: newbie spraying question

#8

Re: how much pressure...

del schisler

on my HVLP finishline spray gun i use 30 lbs with a #2 nozel . I spray lacquer all the time this works for me. I thin my lacquer which is M.L.CAMPBELL about 20 percent . I also have a small inline filter at the gun and one on my compreser. The compreser is husky 30 gal with a external compreaser. So far it works fine. I use it every day for a couple yrs or more. It's cost's was around $500 range not that the dollar make's it better. You get what you pay for. I wouldn't buy a pancake style compreser that is just me.

Re: newbie spraying question

#9

Re: newbie spraying question

TomD

I have a Badger detail gun I spray furniture and guitars with, occasionally, and weather permitting. Works great. For a while my neighbour's brother was around and he was a tech for a spray company. He has some huge spray set up looked like a nuke, all shinny stainless, and some huge compressor. He could do refinishing, paint your room, or shoot tar for your driveway. I learned a lot from that guy, and he was real pleased with the medium price HVLP guns the ones that have flashy anodizing. We get them from some place maybe a little better than HF, and they are sold in singles for about 35 bucks. I keep several around in case I need to spray something I don't want to clean out. Not that they are so bad, but that's how I use them. I don't worry about overspray as far as the environment is concerned. It would do more damage driving to the store that I would recover in a the lifetime of the gun.