Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

PC 333 RO Sander Spitting Dust

Posts

PC 333 RO Sander Spitting Dust

#1

PC 333 RO Sander Spitting Dust

Robby Wright in San Marcos, CA

I haven't been able to figure out why, but my PC 333 random orbital sander doesn't seem to pick up dust as well as it used to. I cleaned the dust canister carefully and blew the dust out of its pores. I checked for blockages, but didn't find any. I even replaced that gasket like thing under the pad in case it was the problem. The flapper thingy seems like it is OK. No luck.

I am at the point of seriously considering buying a new sander. I am tired of eating dust. Any ideas for a fix?

Robby Wright

Re: PC 333 RO Sander Spitting Dust

#2

I have one of those

Bruce, a MN Galoot

and I agree that the dust sucking ability isn't quite what it should be. Neither is the canister that seems to detach without provocation. Its sanding ability isn't bad, though.

A buddy recommended his Bosch, and I sure wish I'd gotten that one instead.

Re: PC 333 RO Sander Spitting Dust

#3

Re: PC 333 RO Sander Spitting Dust

Barry Irby

I leave off the canister and attach the wand form the shop vac to it. Its a tight but perfect fit with the wand that is about one inch. I use that as a handle when sanding large surfaces and it works great. Something of a PITA on small parts where you need lots of mobility. I bought a smaller diameter hose kit for a shop vac and have an adapter or it that goes to my DC or shop vac.

Re: PC 333 RO Sander Spitting Dust

#4

Jason Roehl in Lafayette, IN

Re: PC 333 RO Sander Spitting Dust

Jason Roehl in Lafayette, IN

Hook up a shop vac.

The on-board collection on every RO sander I've seen is pretty much an afterthought at best.

Think about it like this--all these sanders are more or less in the 2-3 amp range (1/4-1/3 HP, tops). That's not a lot of power, certainly not enough for any significant airflow or suction, which are what it takes to pull sanding dust away from your workpiece. Never mind that you want those ponies to go to sanding...

Jason

Re: PC 333 RO Sander Spitting Dust

#5

Re: PC 333 RO Sander Spitting Dust

Jason Waters

I have used the PC vacuum hose since day one. I doubt it's made anymore, but it works well. I hook it to a shop vac.

Re: PC 333 RO Sander Spitting Dust

#6

Re: PC 333 RO Sander Spitting Dust

Harry Ludke

I also have the PC 333. I always connect it to my shop vac for maximum dust collection performance. This past year I added the Oneida Dust Deputy Cyclone to the shop vac as a prefilter. It does a great job collection the dust. I don't remember the last time I had to clean out the shop vac. The cyclone keeps the shop vac performing at it's peak and really helps keep down the finish sanding dust.

Re: PC 333 RO Sander Spitting Dust

#7

Re: I have one of those

Robby Wright in San Marcos, CA

I have heard about the Bosch. It will definitely be on my list of sanders to look at if I decide to replace it. Thanks.

I heard that the PC 390 series is supposed to be good. Any comments?

Re: PC 333 RO Sander Spitting Dust

#8

Re: PC 333 RO Sander Spitting Dust

Robby Wright in San Marcos, CA

I tried hooking up my 1 1/4" vacuum hose, but it was so heavy that it steered the sander. Part of the problem probably was that I didn't have a good adapter.

Re: PC 333 RO Sander Spitting Dust

#9

Re: PC 333 RO Sander Spitting Dust

Robby Wright in San Marcos, CA

You are probably right about that. The weird part is that I think I remember it doing a better job of collection than it does now. Of course, that memory part could be where the problem lies.....

Re: PC 333 RO Sander Spitting Dust

#10

Re: PC 333 RO Sander Spitting Dust

Robby Wright in San Marcos, CA

Jason - That hose is still made. I have had my eyes on it for awhile. I may just have to get it. It was about $35 at my local Tool Mart. Glad to know it works.

Re: PC 333 RO Sander Spitting Dust

#11

Re: PC 333 RO Sander Spitting Dust

Robby Wright in San Marcos, CA

Harry - I have the Rockler Vortex unit, which seems to work fairly well with ordinary shop dust. I will be curious to see how it works with the sander once I get the hose.

Have you had any problems with the vacuum sucking the sander down to the surface you are sanding? I read somewhere that that can be a problem.

Re: PC 333 RO Sander Spitting Dust

#12

Re: PC 333 RO Sander Spitting Dust

Jason Waters

I paid full price, and it was like $25-30 10 years or more ago. It was worth it.

Just a note, do not hook it to your DC if it's not easy to clean the filter (mine is internal-I would never buy one like that again), it will load up with sanding dust. While you are at it, but a Cleanstream or Goretex filter for your shop vac.

Re: PC 333 RO Sander Spitting Dust

#13

Re: PC 333 RO Sander Spitting Dust

John in Calgary

As for what hose to use, I just recently found out that the hose that comes with a drywall vacuum sanding kit (~$20 at the Orange Borg) has an adapter that fits the sander's nozzle perfectly and doesn't pull the sander off my bench when I set it down, like my normal shopvac hose does. Only problem I found was the hose carries a lot of static electricity in the dry dry winter air up here in Calgary, so you get lots of shocks if you are holding the hose while sanding.

John


img

Re: PC 333 RO Sander Spitting Dust

#14

Re: Static charge problem

Larry Clinton At Frankfort, (Central) Indiana

John, if you want to reduce or eliminate the static charge building up in your hose - mix up a solution of "Downy" or similar fabric softener and water (about 50/50) and either spray or dip the hose in the solution, and allow to drain and dry - once dry it should eliminate the problem and should last for several months.

Re: PC 333 RO Sander Spitting Dust

#15

Re: PC 333 RO Sander Spitting Dust

Harry Ludke

Robby, I've never had a problem with to much suction at the ROS head. I'm using a Fein Turbo III for my shop vac. It's got a lot of suction for a shop vac. I think you'll like your Rockler Cyclone.

Re: PC 333 RO Sander Spitting Dust

#16

Re: Static charge problem

John in Calgary

Nice, I'll give that a try. Probably won't work with dry sheets :) (which we have around the house), so I'll have to pick up a jug.

Thanks,

John

Re: PC 333 RO Sander Spitting Dust

#17

PC 390

Dave Bair, Eaton Rapids, MI

I got one about a year ago. It is a much better sander than the 333 it replaced. As a bonus, no vibration is transferred to your hands; no more numb fingers or thick vibration-dampening gloves are needed. It has the 8-hole design as opposed to the 333's 5-hole. My Fein will suck it tight to the wood until the filter gets a little dirty. The motor is brushless which should reduce maintenance.

Re: PC 333 RO Sander Spitting Dust

#18

Re: PC 333 RO Sander Spitting Dust

Robby Wright

Thanks for the idea, John. I give it a look. Definitely less costly than the PC hose.

Re: PC 333 RO Sander Spitting Dust

#19

Re: PC 333 RO Sander Spitting Dust

Robby Wright

Your vacuum is probably stronger than my Ridgid, so I won't worry about it.

So far, I have been happy with the Vortex unit, except for its size. My shop is small - about 3/4 of a double car garage minus the space SWMBO decides to claim. I am thinking about figuring out a way to stack the two. I made a long hose out of a 10 foot piece of 2 1/2" DC host from Rockler. Added an elbow and a swivel connection and it works better than the original hose.

I am curious to see how much stuff migrates from the Vortex to the vacuum over time.

Re: PC 333 RO Sander Spitting Dust

#20

Re: PC 390

Robby Wright

Have you had any problems with the size of the grip on the 390? I have small hands and one of the things I saw in reviews was that people with small hands ended up with aching hands.

Re: PC 333 RO Sander Spitting Dust

#21

Re: PC 390

Dave Bair, Eaton Rapids, MI

I, too, have small hands so I share your concern. If you are going to sand horizontally on a bench, all you have to do is guide the sander and there is no hard gripping required. If you were to sand a vertical surface or overhead, it'd probably be a problem. I tend to sand before I assemble a piece, so I'm always sanding horizontally or I rotate the piece to avoid a long session of vertical sanding. I've also two-handed it when I sanded a door I didn't want to take the time to take down. It is a heavy sander with a wide profile and low center of gravity.

Re: PC 333 RO Sander Spitting Dust

#22

Re: PC 390

Robby Wright

Thanks, Dave. I do like to do as much sanding as possible before assembly, but that last little bit still needs to be done. Sounds like I need to go play with one and see how it fits.