Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

Two Spray Finish Questions

Posts

Two Spray Finish Questions

#1

Two Spray Finish Questions

Robby Wright

I am finishing a stand-up desk for my boss. It is made from cherry and cherry plywood. After sanding for hours, I applied the first coat of TransFast dye and it looks good. A bit of blotching, but I can live with it.

I am planning on using General Finishes PolyAcrylic Water Base Top Coat, using an HPLV conversion sprayer with my air compressor. So here are my questions:

1. Can I spray the top coat directly on the TransFast dye or do I need a shellac coat to prevent bleed?

2. Is there an easy way to clean the spray gun? I have avoided spraying because of cleaning the gun. Spray for 10 minutes and spend a half hour cleaning. I would rather be butchering wood! For cleaning after the dye, I removed any leftover dye, removed the cup and cleaned it, then ran water through the cup connector until it ran clean. Finally, I put water in the gun and sprayed it to make sure nothing remains.

Your help is appreciated.

Robby Wright

Re: Two Spray Finish Questions

#2

1/2 hour to clean!?!

Bill Tindall

If you really don't like cleaning buy what you need to use the 3M PPS disposable cups. Frugal as I am I use then for their convenience.

But really, cleaning a gun is a 1 minute operation. Add small amount of solvent to cup, swish and spray it all out. Repeat twice more. Wipe cap and cup with solvent. Done

Re: Two Spray Finish Questions

#3

As to your first question.....

Howard Acheson

Assuming you used a water based dye, you should apply a coat of dewaxed shellac. The waterborne finish will re-dissolve the waterbased dye and cause a "muddying" of the first coat of finish. Be sure to use a dewaxed shellac as waterborne acrylic finish does not adhere well to shellac that contains its natural wax.

Re: Two Spray Finish Questions

#4

Re: Two Spray Finish Questions

Mark Mandell - Gone Round In Jersey

1st. Question: Yes. Apply 2 light coats of dewaxed shellac, sanding or synthetic wool lightly between them to catch and raised fibers.

Rinse the gun with fresh DNA, then put in a half cup of water and spray that to get rid of the alcohol.

2nd Question: "PolyAcrylic" is primarily a brush-applied product. You'll get much better results spraying with General's waterborne High Performance Polyurethane or their Enduro Clear Poly product.

3rd Question: To clean the gun after the final coat of the top finish, rinse it, inside and out with running water, then fill the cup half way with water and a drop of dish detergent, close & shake well, spray it all out, do final rinse with clear water. Should be all you need.

Re: Two Spray Finish Questions

#6

Re: Two Spray Finish Questions

Robby Wright in San Marcos, CA

Bill and Mark - Thanks for the info. That validates what I did this last time and is much faster than stripping the whole gun down.

Re: Two Spray Finish Questions

#7

question

Bill Tindall

" then put in a half cup of water and spray that to get rid of the alcohol."

How would this step be beneficial? Alcohol will evaporate quicker than water and alcohol is less corrosive to aluminum than water.

I think best practice is to rinse the gun three times with a good solvent for the finish used and then let the solvent simply evaporate from the gun.

Re: Two Spray Finish Questions

#8

Answer

Mark Mandell - Gone Round In Jersey

In the questioner's scenario, he would apply the shellac, allow to dry, clean his gun, then follow with the waterborne.

The shellac gets cleaned out with the alcohol. However, before running a chemically complex compound like waterborne finish through the same gun, it is best to make sure that all of the alcohol rinse is removed to avoid conflict with the tail solvents and emulsifiers in the waterborne; depending on mere evaporation is not, in my view, "best practice" in this situation. As water is miscible with the alcohol which is hydroscopic, the water rinse does the best job of removal. Since most all wet parts in guns are now stainless steel, the water is completely harmless.

I also find it beneficial to first "wet" my gun with the carrier/solvent/diluent of the finish that I'll be spraying. Running a bit if alcohol, water, or lacquer thinner through the gun before filling with finish seems to make the gun easier to clean later.

Re: Two Spray Finish Questions

#9

Re: Answer

Robby Wright in San Marcos, CA

"As water is miscible...."

Wow! I though I had a pretty good command of the English language. Had to think about that one. Good word! Learned something new.

And thanks for the info on rinsing with water to clear out the alcohol.