Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

Delta 22-660 (DC-33) cutterhead wrench

Posts

Delta 22-660 (DC-33) cutterhead wrench

#1

Delta 22-660 (DC-33) cutterhead wrench

NickinMass

I know there are some 22-660 owners out there from reading Charlie Lenz’s thread on the 22-650 he just bought¸and I’m hoping one of you can help me. I recently bought an early-90’s vintage 22-660 (runs great, but needed the dust hood I just finished and some new knives), but it didn’t come with the wrench for the bolts that clamp the knives in the cutterhead. The online parts places say that Delta has discontinued the wrench (helpfully neither the parts list nor the manual lists the wrench size), so I can’t order one. I've tried a 10 mm (seems sloppy and likely to round over the bolt heads) and a 9mm (too small). Does anyone out there know what size wrench this is?

Re: Delta 22-660 (DC-33) cutterhead wrench

#2

conversion chart link

del schisler

here is a conversion chart

http://www.csgnetwork.com/wrenchsizetable.html

Re: Delta 22-660 (DC-33) cutterhead wrench

#3

Are you sure it's metric?

Neal in San Jose

A 3/8 falls right between a 9mm and a 10mm.

Re: Delta 22-660 (DC-33) cutterhead wrench

#4

Re: Delta 22-660 (DC-33) cutterhead wrench

NickinMass

Cheap 10mm (well, actually somewhat expensive wrench from the local hardware store, but apparently not a good quality one) was the culprit. I did what I should have done originally, and went to the local tool store. I got a 10mm and a 3/8" wrench, and found that the new 10mm did the trick (although I did have to grind it a little thinner).

Re: Delta 22-660 (DC-33) cutterhead wrench

#5

Re: Are you sure it's metric?

Charlie Lenz

The DC-33, 22-650 that I bought I found out today uses a metric allen wrench for the feed roller adjustment screws. But that Planer was made in Brazil so it doesn't suprise me much. I also noticed that the Manual that I got with the Planer is for the newer DC-33 models, 22-660, 22-661, and 22-671. The gear box is moved to the other side, and there are no handles on these models. Eventually I'd like to have the Manual for the 22-650, along with the parts breakdown. Nick, I'd like to see the dust hood that you put together.

Re: Delta 22-660 (DC-33) cutterhead wrench

#6

Re: Are you sure it's metric?

Jason Waters

Charlie,

Have you looked at the Vintage Machinery website. Try this link for a manual:

http://vintagemachinery.org/pubs/detail.aspx?id=4183

You can search for others too if that's not the right one.

Re: Delta 22-660 (DC-33) cutterhead wrench

#7

Also, Service net

Jason Waters

Service net has the manual, parts diagram, and what parts are still available:

http://servicenet.deltamachinery.com/

Type in your model number under "find parts", and the result will ask you for type 1 or 2. Then you will see three PDF's you can open, two exploded diagrams, and one manual, seems to be the same as the one I gave you before.

Hope this is what you are looking for.

I use this all the time to look up stuff.

Re: Delta 22-660 (DC-33) cutterhead wrench

#8

Re: Manual, thanks guys

Charlie Lenz

I found the Rockwell version the other day in the OWWM site, and tried to print it out but the black ink in our printer is really low. Then I looked in ServiceNet and for some reason I couldn't find it, but now I did, the Rockwell version pops up also. I think I'm going to load the files onto a flash drive and see if Staples can print the Manual and Parts diagram. Maybe the quality of printing will be better also.

Re: Delta 22-660 (DC-33) cutterhead wrench

#9

Re: Are you sure it's metric?

NickinMass

Charlie - I started with a piece of 2x2” steel angle and a 90 degree wall stack boot (12” wide x 3 ¾” to a 6” round inlet), which I had to mailorder (couldn’t find a ductwork supply place near me – not to say that there isn’t one, but if there is it is fairly well hidden – and the size was apparently not stocked at the local Borgs). I trimmed a bit from the bottom lip, then riveted it to the horizontal leg of the angle. The top lip clips right on to the top of the chip chute. The steel angle is attached using bolts into the 2 threaded holes that are intended for the OEM dust collection hood (no longer made). I used a short offcut of 6” snaplock pipe, crimped at both ends, to connect the boot to my 6->5” adaptor (I still need to rivet and tape those joints). I don't have any pictures uploaded to a place that I can link to, but I can email some if can share your email address.

Looking at the pictures of your 22-650, the same approach should work for you (I think I can see those same mounting holes in the casting on the outfeed side of the planer).

If I can insert a small gloat in here, I got the new knives in and the thing works great – better surface on the wood, quieter, able to take a deeper cut, and less prone to snipe than my Dewalt lunchbox (of course, I didn’t risk injury to myself and a friend getting the Dewalt down into the basement…).

Re: Delta 22-660 (DC-33) cutterhead wrench

#10

Re: Are you sure it's metric?

Charlie Lenz

Photobucket is what I use to display pictures on some sites. It's easy and it's free.

Re: Delta 22-660 (DC-33) cutterhead wrench

#11

Re: Manual, thanks guys

Jason Waters

Charlie,

I checked out the pics of your new planer, and it looks like a nice machine. I hope you enjoy it.

Jason

Re: Delta 22-660 (DC-33) cutterhead wrench

#12

Re: Are you sure it's metric?

NickinMass

Ok, how about this:


img

Re: Delta 22-660 (DC-33) cutterhead wrench

#13

Re: Are you sure it's metric?

NickinMass

And this:


img

Re: Delta 22-660 (DC-33) cutterhead wrench

#14

Re: Looks good Nick, nice job.

Charlie Lenz

That should work very well with an overhead ducted DC system.

Re: Delta 22-660 (DC-33) cutterhead wrench

#15

Re: Looks good Nick, nice job.

NickinMass

The drop for the planer is overhead - it gives me more flexibility for moving the machine around (I have an L-shaped basement shop with a big beam cutting off one leg, so the DC and machines are clustered and mostly on wheels). I have a straight boot that I thought about using instead, but the 90 degree boot seemed to fit the overhead drop better. I would have put it together the same way if I had used the straight boot.