Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A natural, durable finish with minimal coats and fuss popular among woodworkers, flooring professionals, and furniture makers

Hinge Name and Source

Posts

Hinge Name and Source

#1

Hinge Name and Source

Allen Bryant - Bumpass, VA

I'm helping a friend put some doors on his shed and he wants to the doors to swing out due to the small size of the shed. He doesn't want the exterior T-hinges because the screws can easily be removed and the doors taken off the shed without unlocking them. I know they make a standard hinge that has a pin that can't be removed either with a set screw or can be crimped after installing the pin. I'm not sure what to call them to know what to search for. Home Depot is calling them Non-Removable pin hinges, but they only have them in sizes up to 3" and with the door made from 2x stock I'm thinking at least 4 to 4 1/2" hinges would be better. Is a "non removable pin hinge" the proper name and any ideas where I could get them?

Re: Hinge Name and Source

#2

Re: Hinge Name and Source

Jim Breeden

I made my own "non-removable" pin. Using 4-1/2 " hinge, I opened the hinge, drilled a hole in one of the pin tubes, into the pin, just large enough to accept a #4 nail, then cut the nail down to size to allow the hinge to close When the door is closed, the nail is not visible, and the pin cannot be driven out of the hinge. Hopes this helps.

Re: Hinge Name and Source

#3

Re: Hinge Name and Source

Allen Bryant - Bumpass, VA

Thanks that's definitely an option I will keep in mind, can you still remove the nail and pin if you need to?

Re: Hinge Name and Source

#4

Re: Hinge Name and Source

Jim Breeden

Yes - I left just enough pin showing to be able to grab it with pliers, if needed. I built a garden tool storage shed, and wanted the door to swing out, with the only thing showing was the hinge pin. It's been working this way for the last ten years.

Re: Hinge Name and Source

#5

Re: Hinge Name and Source

David Yoho

Allen, my shed has 2-by constructed doors. It was built by Heartland and they used a continuous or piano hinge the length of the doors. Very secure and plenty strong. I don't have a source for them but a Google search should turn up something.

Re: Hinge Name and Source

#6

Re: Hinge Name and Source

Bill Houghton, Sebastopol, CA

Two other possibilities:

1. You can use T or strap hinges, drill through the framing/door, and use carriage bolts with the heads on the outside. You should file the holes square, so the carriage bolts nestle down into the hinges.

2. You can use a regular butt hinge, but drill through the hinge leaves for a bolt (I'd use a Grade 8 bolt, a little harder to cut) that you then epoxy into the framing on one side, after the hinge is installed, after cutting the head off the bolt. You need just enough bolt to penetrate the opposing hinge leaf.

Re: Hinge Name and Source

#7

Re: Hinge Name and Source

Jason Waters

Are you face mounting the hinges?

If so, the t-straps and carriage bolts are your best option.

If you are mounting them like a normal door with just the hinge exposed, they make hinges with anti-theft dimples in them in just about every standard size, and the they are usually standard. The old nail trick works well too. You can always weld the top of the pin in too, but that presents other issues.

Re: Hinge Name and Source

#8

Re: Hinge Name and Source

Allen Bryant - Bumpass, VA

We are planning on mounting like a normal door, going to do it this weekend hopefully. We thought about welding it in, but #1, neither of us has access to a welder and #2 it's two permanent. I've got some butt hinges that I found last night rummaging through some boxes, tonight I'm going to try and drill the holes for the nail trick.

Re: Hinge Name and Source

#9

Re: Hinge Name and Source

Jason Waters

I'd use at least an 8d nail, that's what my father always did on an outward opening door, and he is a General Contractor. Before the days of hinges with the anti theft tabs. Also, most jambs have enough give for the tabs to come out if you take the pins out, but with the nail trick, if you set it up right, you can get a good 1/2-3/4" recess and it's a lot harder. You just want to slow someone down.

Re: Hinge Name and Source

#10

Modify a strap hinge

Lee Schierer McKean, PA

Another option would be to modify a large strap hinge with 2 bends (one on each leaf the thickness of your door) so the straps are inside and only the cylinder of the hinge is on the outside. Secure it with carriage bolts from the inside with the nuts on the inside and it should be pretty much tamper proof.

Lee


img