Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Nearly 100 Exotic Wood Species, Direct-Imported Since 1972. Shop Slabs & Turning Stock.

Warped bandsaw table insert

Posts

Warped bandsaw table insert

#1

Warped bandsaw table insert

Adrian

I noticed that the aluminum table insert in my bandsaw is warped down, I guess from the blade pressing work into the insert. The warping is sufficient that parts of the insert stick up above the table around the edges, which seems like a bad thing.

Now I suppose I could go to Grizzly for a replacement insert. But I have also noticed people selling plastic zero clearance inserts. Is it reasonable to use these plastic inserts all the time? Or will it get bend out of shape like the aluminum one---only much faster since it's a soft material?

Re: Warped bandsaw table insert

#2

Re: Warped bandsaw table insert

Doug Adams

I have used the plastic inserts for several years and they work fine.

Doug

Re: Warped bandsaw table insert

#3

Z-C Inserts

Mark Mandell - Gone Round In Jersey

These things are "consumable" items since, given blade movement, they remain zero clearance for a limited time. Chances are you'll replace them before they warp or sage.

Pretty easy to make your own from 1/4" Lexan (not plexi as it's too brittle) scrap using a fly cutter on a drill press, then back0cut the underside to match your table level.

BTW, for cross-cutting with zero clearance, I use a sled.

Re: Warped bandsaw table insert

#4

Re: Z-C Inserts

john lucas

I think I bought my plastic ones from Carter but I'm not sure. It's about 6 years old and other than it not being zero clearance anymore (thanks to some bad catches while cutting green wood) it seems to work fine. Mine was just very slightly too thin so i put about 4 drops of CA glue on the aluminum shelf and carefully carved them down until it fit perfectly flush. It's been that way ever since I did it.

Re: Warped bandsaw table insert

#5

Re: Z-C Inserts

Adrian

I don't necessarily need zero clearance, though I'll admit there are times when it would have been a good thing. (I suppose cutting down on tearout would be nice.) Can you use the same zero clearance insert with different width blades as long as the blades have the same thickness?

If I need to replace the insert every month that would be kind of annoying. When I tried a fly cutter type device on my drill press the sideways forces caused the chuck to fall off the arbor. I'm afraid that didn't encourage further experimentation.

Maybe I should ask this question: is it weird that my aluminum plate got warped? Or is that a normal thing to be expected? I've had the saw about 6 years.

Re: Warped bandsaw table insert

#6

Re: Z-C Inserts

Adrian

I forgot to ask about the use of a sled. Do you have a sled that rides against the fence? Or do you have no lead? I have found that I can do short cross cuts with my mitre gauge, but the saw doesn't like it. I mean, it has a nastier sound, and I think the finish is not as good. I've always assumed that this was due to cutting against the lead.

Re: Warped bandsaw table insert

#7

Not weird...

John in NM

Mine is warped too, along with wallered out in the blade area from various mis-cuts and other abuses, slivers of wood getting caught, etc. I've also had the insert rotate from vibration and start to catch the blade, that's where some of my warp came from.

One day, in my "free" time, I'll make a nice thick brass one on the lathe at work. In the mean time.... maybe make a plastic or wood one.

Re: Warped bandsaw table insert

#8

Bandsaw Sled

Mark Mandell - Gone Round In Jersey

Morning Adrian,

The sled I mentioned was made for cross-cutting and takes the place of the miter gauge. Since this is not used for ripping, blade "drift" is not an issue. The 1/2" ply has an outside runner that is tight to the outside of the saw table and is then screwed to a HDPE strip that ride in the miter gauge slot. This locks the sled's alignment to eliminate any slop. The shed is then cut half way through and a fence is glued to the top at a precise 90°.

The 1/4" graduations to the left of the blade slot are set to easily cut cheeks and shoulders on tenons and to cut other small pieces that would be risky to hold by hand.

I also use wedges against the fence to cut angles in stock too small for chop or table saw.

PS: Tried to upload the pic, but some other image by some other person keeps popping up. When the haywire gets fixed I'll try again. :D

Re: Warped bandsaw table insert

#9

Re: Bandsaw Sled

Adrian

I don't understand why blade drift is not an issue just because the cut is a crosscut. Seems to me like how much of an issue it is depends on the length of the cut (and of course how much lead you actually have on your saw). And as I noted, it seems like when I cross cut using the miter slot the saw doesn't like it. It runs louder and leaves a rougher finish compared to freehand crosscutting. I've avoided attempting any long crosscuts because I anticipate that they would pull off line. Some of the bandsaw books I've consulted say things like "Bandsaws come with a miter slot but it's basically useless due to blade lead."

Re: Warped bandsaw table insert

#10

Re: Bandsaw Sled

Mark Mandell - Gone Round In Jersey


I think the pic worked this time.

A note on blade lead. I've had the current blade on the saw for about 8 months. I keep the Carter side rollers in contact with the blade, and must say that the Timberwolf blade still cuts straight so "lead" has not been a problem for me.

Re: Warped bandsaw table insert

#11

Re: Bandsaw Sled

Adrian

My lead is about 1/4" and as I recall, there was always lead. Maybe I need to try different blades. It would be nice if there was no lead.

Re: Warped bandsaw table insert

#12

To Be Fair

Mark Mandell - Gone Round In Jersey

I "baby" my blades. No cutting bark or metals of any kind. No curves that start to bind the blade and put lateral stress on on side of the teeth. No pushing the stock faster than the blade wants to take it.

I use Suffolk's Timberwolf blades.

Re: Warped bandsaw table insert

#13

Lead...

John in NM

Unless your blade is severely worn on one side, the blade itself shouldn't be the cause of your lead. If the blade is centered on both tires, there should be no lead on a saw which has co-planar wheels. A dull blade can of course confuse the issue by inviting you to push harder than should be needed. Even a machine with no lead will drift if you have to use a lot force on the cut.

Re: Warped bandsaw table insert

#14

A Tuned Saw

Mark Mandell - Gone Round In Jersey

is, of course, the first requirement. I wonder how many people get their New Toy home, throw a blade on it, assume the machine was aligned at the Chinese factory [laughs and giggles, stage left], and expect it to cut straight.

When I got my JET 18, way back when, I spent some careful time adjusting and shimming "here 'n there" to get it right. Nothing major, nor very technical or hard to do. Getting the wheels co-planer under working tension was job No. 1.

BTW, I tried sharpening a blade once using a air die grinder. Got nice and sharp, but the tooth set was changed and the blade wanted to cut in wiggles. S-canned it.

Re: Warped bandsaw table insert

#15

question

Bill Tindall

Getting the wheels co-planer under working tension was job No. 1.

Will you describe the technique you used?

Re: Warped bandsaw table insert

#16

Procedure

Mark Mandell - Gone Round In Jersey

Sorry, Bill. Missed your question.

1. Unplug the saw.! ;) Remove the doors, table, and fence rail to give unrestricted access to the wheels.

2. Install a blade and tension to the gauge setting.

3. Hand-spin the wheels so that the blade stabilizes on both.

4. Using a depth gauge or a combo square, measure the distance from the front rim of each wheel to the blade at three points, 1) at first contact, 2) top (or bottom) center, and 3) where it leaves the wheel. This will tell you how your wheels sit and whether they are parallel (as opposed to co-planer).

5. If the driver wheel is "cocked" you'll need to shim its mounting to the saw's frame. I had to use a couple of pieces of 1/64" brass foil.

6. If you have to shim the driver, recheck the top wheel's blade-to-rim alignment.

7. You may have to also shim the top wheel which is done by shimming one side of the bracket that the bearing carriage rides in. Again, recheck the rim-to-blade distances

8. With the wheels parallel, take a good straight edge that is long enough to span both wheels, and attach 4 equal spacer blocks that will rest on the rims of both wheels but keep the straight edge clear of the saw frame (I used double face tape). This is the "co-planer gauge". Reinstall and re tension the blade. If all four blocks now make contact with the top and bottom of each wheel rim, your wheels are co-planer. If one set of blocks doesn't make contact, measure the gap from block to rim and proceed to pack out that wheel with washer(s) (I used brass shop-made washers as steel washers that size were way too thick) to bring it out flush and co-planer.

That's what I did when I first got the saw, and I haven't needed to readjust it in the 12 years I've had it.

Hope this helps

Re: Warped bandsaw table insert

#17

Thanks

Bill Tindall

I have not seen the first part of the procedure described before. I have adjustments for all these variables on my big Delta saw so after making the measurements the adjustment will be trivial.