Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

Repairing a Throat Plate Questions

Posts

Repairing a Throat Plate Questions

#1

Repairing a Throat Plate Questions

Barry Irby

Isn't tech insert in a TS called a Throat Plate? The one the Blade rises through?

I have a Rockwell Delta Contractors saw and the plate is made of some sort of pot metal and has become sway backed over the years. Its down a 1/32 to 3/64". Its not flat, so adjusting the leveling screws does not help.

I was wondering about coating it with Bondo and sanding it flat. Will Bondo adhere to pot metal? Is it tough enough too take the abuse of stuff sliding across it? How about covering the Bondo with a piece of plastic laminate? Or would I be better off buying and after market plate? Any suggestions?

Re: Repairing a Throat Plate Questions

#2

Zero Clearance Table Saw Insert

Hoa in Alameda

Why don't you make one (or several) yourself! It's pretty simple to make. Zero clearance insert is safer and cleaner to use. I haven't used the stock insert for years.

My favorite material is 1/2" melamine coated particle board from HD. It's cheap and slick. If you have a plastic store nearby, check their scrap bin for HDPE (material cutting boards are made of).

If you don't have time to make them yourself, they are about $20 a copy.

Re: Repairing a Throat Plate Questions

#3

Quick Answer

Mark Mandell - Gone Round In Jersey

NO! Trash it!

Other answer: I make my tr'oat plates from 1/2" ply, then run them through ("tru") the drum sander 'till they're 1/32" under. Tape to dead flush with alu-HVAC tape, then cut the slot.

Must have a dozen of so for varying blade angles. Spend the $ for the melamine/phenolitics if you wish.

Re: Repairing a Throat Plate Questions

#4

what I do

Bill Tindall

I never use the frail thing that came with the saw. Cut out the plate pattern from something. I have used plywood, Corian, aluminum, HDPE, nylon. Ideally what ever you use will be thinner than needed. Then drill holes where the adjusting screws go. Screw in 1/4" x 3/8" set screws for jack screws. No need to tap holes; just drill undersized holes.

Re: Repairing a Throat Plate Questions

#5

How do you all make the blade slot?

Bill Tindall

If the blade is less than 10" making the slot is no problem- install plate, weight it on each end with my two lead bricks and raise the blade. But what have you found that isn't scary for a 10" blade insert?

Re: Repairing a Throat Plate Questions

#6

Last step

Hoa in Alameda

At the last step, when the new insert is still attached with double-sided tape to the template (an old insert). I put the old insert in the insert opening, turn the saw on, and raise the blade to cut the new insert through the old insert.

Another way: remove the set screws of the stock insert and put it in the opening. Its surface will be below the TS top. Put the new insert on top of the old insert, hold it down with a piece of 4X4, turn the saw on and raise the blade.

Re: Repairing a Throat Plate Questions

#7

Easy and safe

Neal in San Jose

I picked up a 9 inch blade off of a discount table many years ago. I use that to cut enough of a slot that the full-sized blade will fit. You probably already have an undersized blade - use one of the outside blades from your dado set, no need to buy a special one.

To hold the insert in place I move the rip fence over to about 1/2 inch past the "0" on the scale and lock it down. You should check this out before you do it to make sure you won't raise the blade up into your rip fence; It might get noisy!

Re: Repairing a Throat Plate Questions

#8

thanks for those great ideas

Bill Tindall

I think I won't tell abut the scary method I have used, and shall never use again!

Re: Repairing a Throat Plate Questions

#9

I use the fence to hold the insert down...

John in NM

Can stick a wedge in there too if you want it really snug, but I don't go to those lengths. With a 10" blade you can pre-cut the kerf with a smaller blade then go to the 10", since a 10" reaches almost to the table top on my saw.

Re: Repairing a Throat Plate Questions

#10

Jesper, Denmark

Re: Simple and safe.....

Jesper, Denmark

Make the insert and fit it to heigth. Put in saw. Clamp 2x4 on top and have at it.

When you have made the first one and fit it in the cut-out on the saw, take the time to make a few more, using the first one and a router with a top bearing straight bit to make a few more. Handy for different blade thicknesses and Dado blades.

Re: Repairing a Throat Plate Questions

#11

Inquiring minds want to know.....

Barry Irby

You sort of hi-jacked the thread, actually making it much better, thanks, but now we want to know how close you came to the Darwin Award. Do tell.

Now I am looking for some Corian or phenolic.

Re: Repairing a Throat Plate Questions

#12

Re: Inquiring minds want to know.....

Bruce, a MN Galoot

I'd use phenolic because it's much, much stiffer and won't deflect when you stand a piece of heavy wood on it. However, all of my inserts are made of baltic birch.

Re: Repairing a Throat Plate Questions

#13

Don't over think this project......

Bill Tindall

anything will work. I have some thin phenolic that I use and it bendiness has never been a problem.

Warning.....if you use a half inch thickness don't tilt the blade unless you have removed relief from the underside. Now how do I know that?

No comment on Darwin award......

Re: Repairing a Throat Plate Questions

#14

Re: How do you all make the blade slot?

eliotandmax

You may not have lead bricks or whatever. What I have done is to put some longish boards across the insert and clamp them down at the edges of the table. If you want to be really correct, you should sand or plane a very slight curve along these clamping boards and put the belly side( the convex side) down on the table. This step will insure really tight clamping pressure. (Make sure the clamping boards are not in the way of the blade as you crank it up through the insert!)