Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

green plastic splitters

Posts

green plastic splitters

#1

green plastic splitters

eliotandmax

I use a small green plastic splitter in a zero-clearance blade cover( can't remember the proper name for it) on my table saw. The problem is with changing blades to a smaller thickness blade; the cut piece won't go through the splitter because the kerf is too thin. I know I can buy some more of them and thin them down but then I have to find the address and go through the business of ordering, etc. Has anyone had this problem? Any way to make your own?

Re: green plastic splitters

#2

Re: green plastic splitters

Gary Smyth

Wouldn't a credit card do the same thing? Perhaps a piece of thin sliced board, laminate, even artist's poster board? As things go a splitter is a pretty passive device. All you're trying to do is keep the cut section from binding. Any item that will stay in place and not compress ought to do the job. You may need to adjust the zero clearance slot but cheaper and easier than buying store bought thingamajigies.

Re: green plastic splitters

#3

Re: green plastic splitters *LINK*

Jesse Cloud

Those are probably micro-jig splitters. Several of the online woodworking supply companies sell them. Be careful though, as even their "thin kerf" splitters won't work with the really thin blades available these days. The advice above about rolling your own is probably your best bet.


MJ thin splitter

Re: green plastic splitters

#4

Re: green plastic splitters

Dave Bair, Eaton Rapids, MI

I make mine out of washers epoxied into a groove in the insert. You can usually find one to match your blade and they are soft enough to get to the perfect size with a file. I do file a wedge shape on the leading edge after the washer is epoxied.

Re: green plastic splitters

#5

Re: green plastic splitters

eliotandmax

Of course, what you say is true; the problem is that the original splitters have three fairly strong small prongs that fit into precisely located locations on the insert. I haven't figured a way to attach something like this. Don't forget that this splitter has to be removable to make cuts that don't go all the way through the stock.

Re: green plastic splitters

#6

Re: green plastic splitters

eliotandmax

Yes, but now you can't get it out. See my other reply.

Re: green plastic splitters

#7

Re: green plastic splitters

eliotandmax

I suppose what I will have to do is "roll my own" as you all have suggested and then make another zero-clearance insert with no splitter for the cuts that don't go all the way through. Thanks for your suggestions.

My real problem was figuring a way to make these removable.

Re: green plastic splitters

#8

Re: green plastic splitters

Jesse Cloud

Good idea. You can use your current zci as a pattern for new ones. Use the zci as a pattern to draw the shape on some mdf (a little thinner than the recess in your TS), bandsaw or jigsaw the rough shape, doublestick the zci on the mdf and trim with a router and a flush trim bit. You will have an exact copy of the zci. While you are at it, use the first mdf zci as a pattern to make a whole bunch of these. Then you can have one for dadoes, one for angles, etc. etc. Insert some small screws on the bottom of the mdf zci to fine tune the fit so it is flush with the TS top.

Re: green plastic splitters

#9

Re: green plastic splitters

eliotandmax

I went out to walk my bulldog and thought about it some more: I may cut a small sliding dovetail "groove" into my existing zci, where these splitters sit, and make several matching dovetail sliding strips that hold the various thickness splitters. This way I can use washers, credit cards, properly -sized strips of wood, or whatever, and fix them permanently into the matching sliding strips and slide these in and out as needed. Thanks for helping me think all this through.

Re: green plastic splitters

#10

Re: green plastic splitters

Bill White

I don't see splitters as "passive" by any means. Whatever ya do, make 'em fit, and make 'em IMPORTANT.

Bill