Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Nearly 100 Exotic Wood Species, Direct-Imported Since 1972. Shop Slabs & Turning Stock.

safety about cutting rabbet

Posts

safety about cutting rabbet

#1

safety about cutting rabbet

eliotandmax

After all these years it suddenly occurred to me that I've just been lucky. Suppose you're using the table saw to cut a rabbet along a board, say two feet long and 1 1/2 " x 1 1/2 " in cross section. Say the rabbet is 3/4 wide and 3/4 deep so the finished piece looks like an 'L'. You make the first cut, turn the stock 90 degrees and make the second cut. You're using feather boards and a push stick. What I'm worried about -- although I've never had the slightest problem so far -- is the last few inches of the final cut: what's holding the piece that comes out in there? What's to prevent it from shooting out like a arrow? And what's holding up the 'L' -shaped resulting piece for that final inch or so? Am I just getting paranoid in my old age?

Re: safety about cutting rabbet

#2

Re: safety about cutting rabbet

Pat Evans

The cut you describe is dangerous. You should keep the main body, the L shaped piece, against the fence and the cutoff outboard of the blade. Feather board of course will have to be raised to contact the L, not the cutoff.

Re: safety about cutting rabbet

#3

Re: safety about cutting rabbet

Neal in San Jose

You have been lucky. One of these days, that arrow WILL come shooting out. One rule I was taught many decades ago was to never use a set-up that traps wood between the fence and the blade. This will probably lead to a discussion of right-tilt vs left tilt and cutting 45 degree miters, but that's a whole 'nother thread.

What I do is to make the first cut like you do, but then set up the second cut such that it is the leg of the "L" against the fence, and the waste piece is on the non-restrained (outside) of the blade. That way, I am pushing the work piece between the blade and the fence, using push blocks, feather boards, etc to help maintain control. On a cut like you are describing, I would use a feather board or two spaced up above the blade and pressing against the horizontal (top) leg of the "L" to keep the work piece against the fence and a push block to move the work piece thru the cut.

My saw is equipped with a riving knife which will keep the "L" from rotating away from the fence, so it's next to impossible that it will get trapped and thrown. But, even before I had this saw and was using a cheap Craftsman, I did it this way. I've never had to pull a workpiece or scrap out of my tummy!

Re: safety about cutting rabbet

#4

Re: safety about cutting rabbet

John McGaw

What they said plus: don't stand in the line of fire. If you do everything right to the best of your abilities and something still comes shooting out it will do less damage if you aren't directly down range.

Re: safety about cutting rabbet

#5

Re: safety about cutting rabbet

eliotandmax

Ah ha! I'm not crazy! And it turns out that I have been using the feather board to push in the way you have said and with the piece that comes out on the outboard side. So I've gotten away with it. Still, I wonder why that piece didn't get trapped between the blade and the feather board itself. The next time I think I will use something to hold the feather board up above that piece so it is free to move outboard. Thanks for your responses.

Re: safety about cutting rabbet

#6

simple cheap solution to your angst

Bill Tindall

Use the small, 7/12 or 8", 40T combination blades I have recommended for some time. They don't throw stuff.

another solution is to rabbit the edge of a wider board and then rip off the narrow piece.

Re: safety about cutting rabbet

#7

Re: safety about cutting rabbet

del schisler

cut the up right piece first than the last cut will be the board flat on the table . Of course the small piece will come on out but you will be out of the way and can control it better. OR On the out feed hold the small cut piece with the left hand well in frount of the blade over the end feed edge of the saw and the end piece will not come shooting out the infeed side. I didnt read any other post yet.

Re: safety about cutting rabbet

#8

Re: simple cheap solution to your angst

eliotandmax

Thanks for the email. I like the idea of using the smaller 40 tooth blade, along with the other ideas. I've thought about the wider board approach. But it's not so good for me because I want to make picture frames, and I usually start with a long smaller board. I have even been thinking of making just the first cut on the table saw and then putting the piece in a holding jig and making the right angle cut with a hand held router.

( I'll bet the hand tool guys are laughing their heads off about all this!)

Re: safety about cutting rabbet

#9

Re: safety about cutting rabbet

eliotandmax

I had a relative who lost several fingers because he tried to hold something on the far side of the blade and his hand somehow got pulled back through the saw!

Re: safety about cutting rabbet

#10

Re: safety about cutting rabbet

del schisler

No body has used a router and router table. that would be a better idea of course if you don't use a router and router table. My self i have 5 router's and 5 router tables and use them every day. I have a 3/4" rabbet bit that would do that cut in a couple pass's and be safe'r. Oh well don't stand in line of fire and cut it on the table saw. If you know their is going to be a kick back for sure let it happen and be done . Not the safest thing but if no router table Make the up side cut than move the fence and cut the 3/4" off the left side of the board than.

Re: safety about cutting rabbet

#11

Re: safety about cutting rabbet

Dave Bair, Eaton Rapids, MI

I use a stacked dado and do it in one pass.

Re: safety about cutting rabbet

#12

Re: safety about cutting rabbet

Jim Breeden

I always skin 'em first. :D

Re: safety about cutting rabbet

#13

Re: safety about cutting rabbet

Jim Dillon

A slight variation to safely cut a rabbet that I don't think was mentioned is to not cut all the way through on the second cut. Leave just enough that you can break the waste piece off by hand, then clean up the rabbet (if necessary) with a shoulder plane. I often do this when I actually want to KEEP the waste when cutting ebony strips that will end up as plugs for G&G furniture.

Jim

Re: safety about cutting rabbet

#14

Re: safety about cutting rabbet

John in NM

I usually organize my cuts such that the drop piece is on the outside of the blade relative to the fence, to avoid the missile problem. When this is unavoidable, I make sure not to stand in the path of the possible projectile :D I've seen it happen often enough when I worked in a shop with others, I don't remember ever having it happen to me, leading me to think there is almost always a way to re-organize your cuts.

Also, I routinely use two push sticks, one for each hand. The right handed one is a typical pusher, made of plywood. The left hand one is a stick with a wedge and L cut in the end. It is used as a "mobile" splitter, behind the blade, and keeps the kerf open and the wood pressed up against the fence. I haven't made a scary cut in years using this combination. If your rabbet cut is arraigned so the L piece is against the fence, the second push stick would help you control the cut.

Ideally, all saws would have a splitter and effective guarding system, but our world is far from ideal so we adapt to what we have.

Re: safety about cutting rabbet

#15

Re: safety about cutting rabbet

eliotandmax

Yes, but you see, if you think hard about it, what's holding up the board other than the stacked dado blades near the end of the cut? You still have to think carefully about using a feather board to push against the work piece.

Re: safety about cutting rabbet

#16

Re: safety about cutting rabbet

eliotandmax

Yeh, but I didn't misspell 'rabbet' this time!

Re: safety about cutting rabbet

#17

Re: safety about cutting rabbet

eliotandmax

I'm sorry, but I can't picture your mobile splitter. Can you explain it better? Remember that the second cut does not go all the way through.

Re: safety about cutting rabbet

#18

Re: safety about cutting rabbet

gary camp Bend, Oregon

I must be missing something. What do you mean what/s holding up the board other than the stacked dado head? The portion of the board not being removed, is what is holding up the board. Are you using zero clearance throat plates on your saw?

glc

Re: safety about cutting rabbet

#19

got a picture finally

John in NM


Obviously it doesn't hold the kerf open on a blind cut like this. The drop piece is removed for clarity. Right hand push stick not used, had to work the camera :D

Re: safety about cutting rabbet

#20

Re: safety about cutting rabbet

eliotandmax

O.K. I'm worried about what you're doing when the board is narrow and you are at the last inch or so of the cut. So most of the board is not there any more, right? The only piece of wood actually touching the table has a cross section of just a few square inches. Imagine, to make my point better, that the thickness of the 'L'-shaped part of the board that is up against the fence is really small -- say 1/4 inch. Doesn't that make you nervous? The work piece wants to tilt over to the left right on top of the dado blades. You need a good feather board pushing hard against the fence. Perhaps I'm not explaining things very well. Others are worried, too, about this cut.

Re: safety about cutting rabbet

#21

Re: safety about cutting rabbet

AZ in Colorado Springs

If you've got a piece of wood 3/4" or 1" wide and you're cutting a half inch rabbet out of it, that piece of stock is too narrow. You need to start with a wider board, cut the rabbet along one edge, then rip the project part from that board. Our use hand tools. (These may not be your exact dimensions, but this sounds like the situation you're addressing.)

To minimize waste, when you get down to the last three inch or so piece of stock (using the arbitrary dimensions in my example) you could cut rabbets on both sides of the workpiece, then rip project parts off the two sides, leaving a narrower strip of waste.