Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

Stock prep, resawing drawer parts questions

Posts

Stock prep, resawing drawer parts questions

#1

Stock prep, resawing drawer parts questions

Barry Irby

I have some poplar that was cut about a year ago and has been drying outdoors under a tarp. Today I pulled out some 5/4 stuff and resawed it for drawer sides. Was trying to get 1/2" stock but don't think I made it.

I skip planed it taking as little material off as I could to get to reasonably flat surfaces and then resawed it on the bandsaw. I have set it in the house with air spaces between to allow it to dry/acclimate. Is this the best practice? Will it cup? Any advice would be appreciated. It ranges from five to seven inches wide

Re: Stock prep, resawing drawer parts questions

#2

Re: Stock prep, resawing drawer parts questions

Bill Tindall

I prefer to dry before resawing. With care you can get 1/2" resaw from 5/4 and the lumber is flat and well sawed to begin with. Drawers don't need to be 1/2". If they wind up 7/16 that is fine.

Re: Stock prep, resawing drawer parts questions

#3

Ellis Walentine

Re: Stock prep, resawing drawer parts questions

Ellis Walentine

Cupping is a function of the moisture gradient in the wood, and it's hard to predict what that might be in your air-dried lumber, so the only way you'll know if (and how much) it will cup is to try resawing a couple pieces. Bringing the wood, which is probably at about 12% MC, into a warm place for a while isn't going to help much because of the thickness. In fact, doing that will set up an even steeper gradient in the wood, as it will dry out the cells on the outside of the board. This will increase the tendency to cup. To equalize the gradient throughout the wood, you'd need to condition it for far longer than you have the patience for in the middle of a project.

So, your approach is about the best you'll do with the wood you've got. Sticker it and weight down the piles after resawing, and you should be okay. Remember, though, that your drawer parts will still be shrinking for a while as they drop to a lower EMC. This may or may not be critical depending on the design.

Ellis

Re: Stock prep, resawing drawer parts questions

#4

Re: Stock prep, resawing drawer parts questions

del schisler

Barrry what you mite do if it cup's ect. I know that this a waste but you could just plane it down to the 1/2" . Poplar is cheep but this way you get cut's on all sides instead of only one side. Unless you cut some off of each side?? stress cut on one side i bet it will cup ? But if you plane it down stress on both side's. It may not cup. I guess you will know soon. I do a lite of resawing sometime's even when sawing the wood it will do it's thing. I alway's cut it bigger than i want just for this reason . Than i have to do the jointer than planer to get it streight again good luck

Re: Stock prep, resawing drawer parts questions

#5

Dale Lenz

Re: Stock prep, resawing drawer parts questions

Dale Lenz

I've done what Bill does for years and it works great. My 1-1/8" rough sawn lumber is about 12% outdoors, bring indoors and sticker-stack. If I put fans on the lumber while I'm in the shop will drop down below 10% in about 2 weeks, no fans about a month. I've not had a problems with wood movement, although most of my stock is milled to 3/4". While working on a flag case run, that will last more than a month, I'll often leave the wood pieces on edge w/ spaces between them.

Good luck

Re: Stock prep, resawing drawer parts questions

#6

More information on drawer sides.

Bill Tindall

I cut 1/8" off the end of a typing finger sheering sheep so I hope you appreciate the pain and suffering to type this. Well only "e, d and c" are painful. Hand tools can be dangerous too!

Cupping can be, and most usually is caused by drying stress and it is only curable by steaming the lumber.

Cupping can be a result of a moisture gradient across the thickness which then dries after sawing. If the lumber is taking a month to equilibrate there isn't any moisture gradient to speak of. I would wager that very few cupping problems are a result of this factor.

Cupping can result from differential moisture loss or regain of one side of a piece relative to the other. This factor is the most common cause of cupped thin lumber.

Drawers are boxes and boxes hold their sides flat. It doesn't matter if the 1/2" pieces cup some, a drawer can be built with such lumber just fine. In fact I have never had perfectly flat thin lumber to work with for something like an 8" wide drawer side. Learn to live with this reality.

Re: Stock prep, resawing drawer parts questions

#7

Ouch! the opinionated finger.....

Barry Irby

on your left hand? Terrible thing. It won't be able to signal your feelings over as great a distance any more. Hope it recovers well and soon. Thanks for the effort.

I almost cut about half an inch off the thumb on my right hand when I was in high school. Not much holding it on and the tip of the bone was gone. Doc wanted to cut it off down to the first knuckle and I would not let him. I still have a gap under the nail, but I am really glad I made that call. Was taking typing in high school at the time. The teacher insisted I could go on, until I bled all over the key board. I still hit the space bar with my left thumb.

Are you shearing with hand clippers like scissors or the electric ones like barbers use? We used the electric ones. It was sort of fun in its own way. Bring them in, sit them on their butt, take their jacket off and watch them go frisking around. They clearly loved getting out of that heavy coat. Aren't you a little early? There's cold weather coming. We did ours a little later in the spring. Or are these indoor sheep? Pets maybe?

I will bring some poplar indoors and let it dry for a year or two.

Re: Stock prep, resawing drawer parts questions

#8

Re: Stock prep, resawing drawer parts questions

George Colonel's Workshop-Havertown PA

Good Afternoon Barry,

Most of the drawers I've built are from air dried and resawn poplar, and I generally shoot for a 1/2" thick side. I've never waited much more than a week or so after resawing to use the wood, which I do sticker and place in my heated celler. I have not had any serious problems with cupping after assembly. I use dovetails on all corners and clamp securely while the glue dries. I believe the joints themselves help prevent serious cupping. Occasionally, when fitting the drawers into the cabinets, I find one or two have slightly cupped, and I address this unhappy fact with my jointer and hand plane.

George

Re: Stock prep, resawing drawer parts questions

#9

Re: Ouch! the opinionated finger.....

Bill Tindall

before lambing the nasty wool from the ewe's behind is best clipped to provide more obvious and cleaner access to nipples. Both wife and I have gotten nasty wounds from hand shears. They are wicked sharp and long so that it can be easy to loose track of the ends.

Re: Stock prep, resawing drawer parts questions

#10

Re: Stock prep, resawing drawer parts questions

gary peterson

I have done this with straight grained white pine 6/4. After is air dried I cut lengths for drawers and backs( usually 22 drawer and 38 back) . I made a small kiln out of rigid foam insulation prob 1/4 or 3/8 thick(not keen on real name) cut hole in side for small space heater to blow in, sticker the wood secure, put kiln over wood , I've had temps to 160. Wood is dry, measure with meter, when resaw pieces stay flat. Then store stock flat unstickered with scab piece over top. Do not put heater inside.