Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

Craftsman insprired board

Posts

Craftsman insprired board

#1

Craftsman insprired board

Dave Paine

My colleague asked if I would make a cutting board for her father. No design details, although I sent her some links to boards made by artisans. The only feedback was a positive reaction to "Craftsman" style.

The other input to the design is that her father is a 'tree hugger' (her words), so preferred domestic renewable woods.

I like to mix domestic and exotic. I love the colours in some exotics. I also love grain patterns in any wood.

So this was my solution.

I had a 1.5in x 6in hard maple board. I cut into strips. I then found the 'side grain' had some curl showing, so decided to make this the exposed surface.

I added inlay's of bloodwood (top to bottom) and purpleheart (side) including purpleheart squares between the strips. The ends are also hard maple, but a different board, so the grain patterns do not match. I wanted the 'bread board' end effect.

This is meant to be the cutting side. The side edges are beveled to accent the craftsman style.


I wanted a side for display, and not intended to be cut and to showcase domestic woods. I had an assembly of two sequential 1/4in panels cuts from a piece of curly maple, my first attempt as popping the grain. I ended up preferring just oil over tinting. This was the left over piece. I cut two 1/4in strips of curly black walnut to fill out the top to bottom side. I then cut a piece of cherry into two sequential 1/4in strips to fill out the left and right edges.

I added some 3/4 by 3/4 feet of black walnut to give the appearance of pinned tennons. The bottom side was also bevelled.

I love the grain patterns in the curly maple and curly walnut.


I like to add inlays to the edges, to try and hide the fact this is two distinct layers. I also prefer to minimize exposed end grain.

The long edges are inlayed with lacewood. The ends are inlayed with Agate Orange. Selections based on the strips of wood on-hand to minimize waste.


The only finish so far is clear 'Butcher Block Oil' by General Finish. This is clear in the bottle, but adds a hue when applied to the wood.

Posting this before I present to my colleague. I emailed some earlier pictures, but the design evolved, as is usual for my projects.

Re: Craftsman insprired board

#2

BarbS

Re: Craftsman insprired board

BarbS

Very beautiful. That is one Classy cutting board. Well done!

Re: Craftsman insprired board

#3

Ellis Walentine

Cutting boards as art

Ellis Walentine

That board almost needs to be on a display pedestal, never mind a kitchen counter. Beautiful workmanship, excellent construction, lovely contrasts, creative motifs ... what else can I say?

Thanks for posting. You've raised the bar.

Ellis Walentine

Re: Craftsman insprired board

#4

Re: Craftsman insprired board

pecker

That looks great. But I wonder what the boards that surround the central area will do when the central area tries to expand, either through seasonal changes or when they get wet.

There is a thread in another forum where the board came apart, though the construction is not identical to yours.

http://www.sawmillcreek.org/showthread.php?178291-Need-a-Hand-Cutting-Board-Failure

Re: Craftsman insprired board

#5

Cutting board?!

Bill Tindall

If it was mine I would hang it on the wall as art.

Seriously, you might consider providing some means of wall hanging.

Re: Craftsman insprired board

#6

Re: Craftsman insprired board

Dave Paine

Water can be the common enemy and treated with care.

I experienced a failure on the first cutting board I made. Simple maple strips glued together without a "bread board" end. The failure was cracking at the end grain due to moisture being absorbed. The board was laid flat on the counter.

Since that experience, I now prefer to minimize end grain. I fixed that board by ripping dado's to cover the splits, adding some black walnut strips for contrast, adding a full length "bread board" end which was cut to have an almost full length tenons at each end and associated mortise in the board. In addition I added rubber feet so the board is never sitting in water on the counter. 10 + years later and it looks as good as after the repair.

I will be recommending the board is not soaked in water, and after being washed down, is placed vertically to drain.

I have made a good number of boards, and so far only my own board had a failure. Many are used for display, so do not get exposed to water.

I made one all end grain board happened to be for the same colleague. This is also put on display, so holding up well.