Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Finishing in humid weather questions...

Posts

Finishing in humid weather questions...

#1

Finishing in humid weather questions...

Barry Irby

I have some jewelry boxes that MUST be finished by Christmas. Its raining today and tomorrow. I was planing to spray lacquer. My son has been finishing his gifts and struggling with blush. Any suggestions? My son has been using Deft in rattle cans, I was planing to use a spray gun, probably with Deft also.

What about Seal Coat Shellac. Two of three coats of that maybe topped with one or two of Lacquer/Deft?

I'm in humid southside VA and don't have a spray booth.

Re: Finishing in humid weather questions...

#2

Re: Finishing in humid weather questions...

Keith Newton

If you can't just turn the heat in your shop high enough, I would look into enclosing a small area, then warm it up with one of those little space heaters.

A couple of weeks ago I sawed a white pine log up for a friend, and kept 65 bf. I stickered it, then suspended a sheet of foam insulation over it a few more inches, then spread a tarp over it, hanging down below the sides loosely. I then cut a little opening in the end for this little ocillating heater to fit into, a then set it on high. It dried that stack of lumber from green to 6% in one week.

I needed the air to be drawn in , and allowed to escape, to carry the moisture away, but you only need to warm up a small space to drop the relative humidity.

Re: Finishing in humid weather questions...

#3

Re: Finishing in humid weather questions...

Barry Irby

I was thinking about that. I can heat up the shop. I was wondering if heating it caused the lacquer to dry faster trapping the moisture or if letting it stay cooler caused more condensation but let it escape more slowly.

Re: Finishing in humid weather questions...

#4

Re: Finishing in humid weather questions...

Earl Kelly

Barry, if you can use a spray gun with your Laq. Get some Laq Retarder. It slows the drying enough to let the moisture out before trapping it. The problem is, usually retarder is only available in 1 gal cans. You only need a few ounces or less per Qt. You might try finding a Finishing shop that would sell you a small amount.

I've used retarder in my Laq to spray when it Foggy as well when it's pouring down rain, just be careful not to have to fast of airflow across the surface of the projects from your exhaust fan.

Re: Finishing in humid weather questions...

#5

Re: Finishing in humid weather questions...

Keith Newton

The cool shop is worse. Warming the air drops the relative humidity, and will also make your lacquer dry faster. That evaporation does cause a drop in temperature, as well as the spray leaving the tip of your gun or can, but it will hit the dew-point quicker when it is cool and damp.

You can also heat up small objects beforehand with a heat-gun, which can speed drying, without as much worry as spraying a cold object, but I wouldn't count on that alone in cool damp air, so heat up your shop or some other space if you can.

Re: Finishing in humid weather questions...

#6

Re: Finishing in humid weather questions...

Larry Clinton At Frankfort, (Central) Indiana

I often spray Behlen Qualalacq lacquer, sometimes in humid conditions. I normally thin the lacquer even though it is supposed to be of spraying consistency. I prefer to spray a few thin coats rather than a couple of thick ones. When spraying in humid conditions (I have sprayed outside and had to quickly move the items into my shop due to rain starting) I use retarder as part of the thinning material (I usually use about an ounce or two in normal temperatures - too much in cold temperatures will really increase the drying time and you risk more "dust nibs"). You can purchase the retarder in quart cans from Grizzly or several other vendors. You might find it at some of your local auto paint stores. It is just a slow evaporating solvent that is compatible with lacquer. Any brand will work. I would spray some firewood first to make sure you have enough retarder, if you do not add enough in high humidity you will get a whitish "Blush" from the entrapped moisture. I never use any "primer" with lacquer and have not seen any need to change. I would try to warm up the shop - mainly to decrease the drying time and reduce dust nibs . As I spray most of my projects outside in the driveway, another use for the retarder is when the temperature is high and the sun is hitting the project, then lacquer that dries too fast will "bubble" and skin over before the solvent has time to escape, adding retarder will allow better flow out and prevent the bubbles.

Re: Finishing in humid weather questions...

#7

Re: Finishing in humid weather questions...

DON in STL

I haven't sprayed lacquer on furniture, but years ago I sprayed quite a few automobiles with lacquer.

Spraying separate, light coats of lacquer, with pleanty of time between coats to allow solvents to flash off helps to minimize the chance of blush.

Sometimes, when the blush is minimal, you can spray light coats of just lacquer thinner on the item and it will penetrate through the lacquer (sort of reactivating it) and as it flashes off it will draw the blush out. I have sometimes had to do this a number of times to draw out all of the moisture.

It doesn't always work, but it doesn't take much time to try when compared to re-doing a project.

Also, lacquer thinner sold at auto suppliers is available in slow, medium or fast evaporation mixes. When beginning the finishing process, it helps to use the proper thinner for the conditions at the time of spraying.

Hope this helps.