Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

Is ther a difference in Pin nails

Posts

Is ther a difference in Pin nails

#1

Is ther a difference in Pin nails

Dustmaker Mike

Howdy All. I have a Freeman 23G pin nailer and it seems to jam all the time. I am using HF pin nails. I use HF 18 & 16 G nails with no problems. I am shooting into Oak trim and have the air pressure set to 90 psi. Just under what the max is for the gun. It seems to shoot 4 or 5 then jam then 8 or 9 then jam. Is it the Oak or the nails or the fool behind the trigger.

Re: Is ther a difference in Pin nails

#2

Dear fool behind the trigger

Barry Irby

I can't answer your question definitively but I have an HF 23 Gauge pin nailer and I am shooting Porter Cable Nails (I think) I have never had a jamb, but I may have shot only a hundred nails or less. Bought a very small assorted pack of nails at HD I think.

There has been discussion here about taking the gun apart and very carefully realigning it when reassembled.

Re: Is ther a difference in Pin nails

#3

Re: Is ther a difference in Pin nails

JMOHNIKE

What type of jam is it. Are the pins getting jamed or is it the drive part. If it is the drive part I would suggest to lower the PSI half way between min and max. I have a HF and a Black and decker pn driver. The HF requires more psi than the B&D, if I don't remember to lower the PSI when I change to the B&D I will get a jam, such as you describe.

Re: Is ther a difference in Pin nails

#4

Re: Is ther a difference in Pin nails

Ken Garlock, Collin County Texas

Hi Mike. I am puzzled as to why you are using 16Ga and 18 Ga nails in a device made for 23 Ga. I don't have access to the manual for your gun, but I did look it up on the net, and I didn't see any references to using the gun for 16 and 18 Ga. nails. Without more information, I can only guess that you have ruined the gun by using grossly over sized nails (16Ga, and 18Ga.)

If I am totally off base, my apologies.

Merry Christmas,

Ken

Re: Is ther a difference in Pin nails

#5

Ken I have a 16 & 18 G guns also

Dustmaker Mike

Just was trying to say I have used the HF nails in my other guns and they do just fine.

Re: Is ther a difference in Pin nails

#6

The pins themselves

Dustmaker Mike

Are bending. I have the arrow up like in the instruction (yes I read them don't take my man card) I might go get some Porta Cable or another name brand and see what I can figure out.

Re: Is ther a difference in Pin nails

#7

Re: The pins themselves

Carol Reed

I had a similar problem. I found that in putting it back together after a jam, I didn't have it PERFECTLY aligned. I took more care and not it works fine. Finicky thing.

FWIW.

Re: Is ther a difference in Pin nails

#8

Re: The pins themselves

Yonak

You say the arrows point up ? The arrows should point in the direction of the shot, unless I'm misunderstanding your indication.

Re: Is ther a difference in Pin nails

#9

Re: Ken I have a 16 & 18 G guns also

Ken Garlock, Collin County Texas

Ahhh-Sooooo.

OK, finally I under5tand.

MY next and last suggestion is to throughly clean and lubricate the gun. And reduce the air pressure as suggested above.

I haven't ventured into the arena of trying to nail ants to the wall. But, I do like my 18Ga Senco.

As said before,

Merry Christmas,

Ken

Re: Is ther a difference in Pin nails

#10

Hum I just looked in the book

Dustmaker Mike

Again and I am not sure what I saw before. It must be the fool behind the tool. Thanks and Merry Christmas all

Re: Is ther a difference in Pin nails

#11

Re: Hum I just looked in the book

nickb

If you've been loading the pins upside down, have a good look at the driver tip - it may be damaged and want replacement...