Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

Windsor chair plans

Posts

Windsor chair plans

#1

Windsor chair plans

Joseph Mulherin

Today I drew up the patterns for my new Windsor Combback chairs I am going to be making this year.

We have a rocker in our house which I used to copy the measurements for the seat, arms, spindles, legs and spacers. The seat is going to be 2 1/4"thk x 22 1/2"wide x 21" long. Will layout the coving and scorp it out to about 3/4" in rear and 1/2" in front...just so the bottom feels comfortable sitting in it without scrunching around to get comfortable. Decided to make them with rockers too.

Rockers are 32 1/2" long with a 2" deep curve x 1 1/4" thk. Decided instead of using the spindles in the seat back I am going to use splats like I used in some furniture I made about 25yrs ago which are 26 1/2" long x 2 3/4" WIDE X 1/2" THK. Have to make the arm spindles yet but patterns are easy to make and follow on my Shopsmith lathe setup. Plan on making about 6 of them for family members...and they will be around for many yrs after I have gone to my "reward"....lol. Besides, it gives me something to do in these retirement years.

Re: Windsor chair plans

#2

JL

Re: Windsor chair plans

JL

Sounds ambitious - but fun :D.

Might I suggest scooping out just a bit more in the rear? With that thickness of seat, you can easily go to 1".

Re: Windsor chair plans

#3

Re: Windsor chair plans

Philip Duffy

JL has it right! Phil

Re: Windsor chair plans

#4

Re: Windsor chair plans

Joseph Mulherin

JL and Phil have it correct. I just laid a steel rule over the rocker seat and measured the depth at three places. In addition... since the chair seems to have been made when people were smaller in stature with shorter legs too, I have decided to extend the length of the seat about 4" so my knees are not extending so far out when seated...anyway a test seat will be done first before final decision. Intend to make the chairs as rockers, but if I decided to not make one of them that way I shall have to extend the length of the legs about 2" each. Might try to make one of the desk chairs too.

Re: Windsor chair plans

#5

Re: Windsor chair plans

john lucas

I've only made 2 Windsor chairs and I love them. However several of my friends made the comment that I need to make them for larger people. Let's face it, American butts are bigger than they used to be so existing plans need to be modified.

Re: Windsor chair plans

#6

JL

Re: Windsor chair plans

JL

Some thoughts.

Sit in a side chair. Have someone measure the distance from the inside of your knee to the floor. This distance obviously varies from person to person. I usually make it so that the height of the chair pommel is about 18-18.5" or so from the floor. For "most" people, this is a comfortable height. I'm about 6' 1" or so - I usually make my "personal" chairs about 19" +/-.

If you are making chairs for tall people, by all means, make the legs longer - just make sure you keep the proportions good. On a baluster style leg, I add a bit of length in the vase of the bulb and the lower part of the leg. On a bamboo style leg, I just stretch everything out.

Re: Windsor chair plans

#7

Re: Windsor chair plans

Joseph Mulherin

Thank you, JL, I shall take those thoughts into consideration when I start the chairs.

The present rocker seat is about 17.5" from the floor....probably should be around 19"+ like you said for the modern people nowadays. The legs and arm spindles will be sized later after I feel out the chair heights. The top of the chairback will be a cove board 27"long x 6" high bandsawed to shape and steamed for the curve needed. The spalts will dowel into this board and into the seat.

Going to ba an interesting project in my retirement years....but doable. I plan on using mostly my powered equipment to make the various parts. I am not familiar with using the spokeshaves, travishers, etc. Am thinking I will drill down with my Fortsner bits to the depth I need at various spots, then use my sidearm grinder with various blades to smooth things out... and then use the ROS to finish up.

Will use dry tint mixed up with water for stain, wipe it down and let dry for a couple days, then wipe on some poly.

Re: Windsor chair plans

#8

JL

Re: Windsor chair plans

JL

I typically have four depth holes about 5-6" from the back and about 2" and 4" from the center line. I drill down to about 7/8" with a small Forstner bit.

I usually use my 4 1/2" angle grinder with a carbide "donut" like the Proxxon. I use a chainsaw wheel for hardwoods. I then go to 36 grit disks.

Re: Windsor chair plans

#9

Re: Windsor chair plans

Joseph Mulherin

I looked up the Proxxon donut and am going to buy one next year to help scoop out the seats like you said.

I like the idea of drilling the depth measuring holes and then wasting away the material till it gets down to workable sanding surface.

Re: Windsor chair plans

#10

Re: Windsor chair plans

Barry Irby

I don't have a Proxxon so I don't know how quickly they work, but (no pun intended) on the last two I did I used an angle grinder with a very coarse sanding disk without a backer. Worked great. These were small child sized seats in walnut and they took about thirty minutes apiece with the grinder. Then another 20 minutes with the ROS.

Also, I used a forstner bit to waste away as much as I could. It was about a two inch bit and I mapped it out like a topo map. Drew the butt print with chalk and visualized where I wanted it at least a 1/4" deep and drilled away that part, then moved into the half inch deep area and so on. The tip on the bit stuck down about an 1/8" so I let that be my depth control. Seemed to work really well.

Re: Windsor chair plans

#11

Re: Windsor chair plans

Joseph Mulherin

Went to the rocker we have in the living room , sat in it and measured from my knee to the front of the seat...between 3-4"was space, so I decided to extend the seat from 18 1/2" to 22 1/2" square seat board and then bandsaw the shapes needed and rounded over and smoothed out. Laid out legs holes and arm spindles holes. Leg holes are to be 17deg x 6deg slant, and arm spindles will be almost perpendicular to the arms.

Am going to be using my Shopsmith saw/lathe/drillpress to do almost all of the work. Six chairs are planned...and maybe one seat desk chair. Thomas jefferson was said to use one of those when he wrote the Constitution.