Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

Splines on the corners of boxes????

Posts

Splines on the corners of boxes????

#1

Splines on the corners of boxes????

Barry Irby

I am making another batch of boxes for Christmas presents. Mitered the corners and am installing splines through the corners by cutting slots through the corner and installing splines and then sanding them flush on the exterior. I have done this many times before and as I recall I ripped the splines with my WWII blade and installed them. Took a couple of tried to get the thickness just right but after that it was easy. I mangled my WWII blade on a staple (See post below) and I can't seem to get it to cooperate at this level. It "appears" to have very minor chipping on the a few of the teeth but apparently that is enough to mess up the cut.

So, how do I do this? I have ripped some strips and they are not smooth enough and not accurate over their length. I ran them through the Performax on a sled. If I send one through and get it just right, then send its brothers through, they come out different. Four come out thicker than one. If I send one through and it is VERY slightly too thick and I send it again without changing anything, its too thin.

So I take the one that is just barely too tight to press in by hand and tap it into place with a mallet? (don't want to split the box) Or do i glue in the ones that are Slightly loose with Epoxy? (gap filler).

And, what do you think of CA for this application, is it permanent?

Re: Splines on the corners of boxes????

#2

JL

Re: Splines on the corners of boxes????

JL

I usually just use yellow glue (Titebond II or III) for my splines.

If it is just a little too tight, I just hand sand it a little. I don't like loose splines - I prefer not to use filler. If my joints are good to go, I usually just "tap" the splines in. I prefer a bit "snug" as opposed to anything else.

Re: Splines on the corners of boxes????

#3

Re: Splines on the corners of boxes????

John E. in SC

I would either hand sand the "too thick" splines, or if you have a good hand block plane, it's easy to take a shaving or 2 with that to make it perfect. I like the splines to be a nice friction fit, where it may take just a tiny tap with a mallet to make it flush, but definitely not too loose.

Re: Splines on the corners of boxes????

#4

Re: Splines on the corners of boxes????

paul in AZ

I make mine a hair too thick, then hand sand to get a firm friction fit. Once in a while I get impatient and give them a light tap with a hammer to snug them in. Never forced though.

Re: Splines on the corners of boxes????

#5

Re: Splines on the corners of boxes????

steve mackay

I sand down my splines to fit individually. Takes time but they look better than trying to fill gaps.

Re: Splines on the corners of boxes????

#6

You Got Good Explinations, Barry


Re: Splines on the corners of boxes????

#7

Re: Splines on the corners of boxes????

eliot d

I didn't a sense of the size of these boxes. And are you talking just about the corners, or the whole length? If just the corners and if the box is not too small, why not use a biscuit joiner? I do it this way for picture frames. The biscuits are very uniform in thickness and, of course, are designed to fit into the slots just right.

Re: Splines on the corners of boxes????

#8

Dale Lenz

Re: Splines on the corners of boxes????

Dale Lenz

Barry...I intentional cut my spline's thickens, for my flag cases slightly over size, maybe 1/16”. Hand plane to fit snug. It has always been my understanding, that a planed surface is best for gluing vs. any other type of a wood surface preparation. If I can hold the flag case up by a dry fitting spline, it's good, that's assuming you planed the spline level, ie no bevel. Best to push splines in with hand pressure only, it you get carried away with a mallet could be trouble. I use regular Titebond yellow glue; don't seem to get as much glue creep with regular yellow glue vs. some of the other yellows.

Re: Splines on the corners of boxes????

#9

Re: Splines on the corners of boxes???? *LINK*

Bill Houghton, Sebastopol, CA

I think Barry is talking about splines that are applied after the fact, to the outside of the box. As I've done them, I make and glue up a miter-jointed box, then cut across the corner and glue in thin strips of wood, which I then plane down. The link below shows a jig for making the slots.

If, of course, I've misunderstood Barry, then this post is irrelevant.


img

http://lumberjocks.com/Don/blog/1702

Re: Splines on the corners of boxes????

#10

Re: Splines on the corners of boxes????

Barry Irby

These boxes are about 8 x 13 by 4 tall. These splines are more like keys through the corner. If splines or biscuits are vertical and concealed within the miter joint, These are horizontal and exposed at each corner. There are there in each corner. The wall thickness is about 7/16" thick. Little Jewelry Boxes. three are walnut with veneered Book-matched crotch wood on the front and the tops, the others are cherry with bookmatched birch crotch wood tops. All the wood is air dried and harvested off the family farm.

Re: Splines on the corners of boxes????

#11

Re: Splines on the corners of boxes????

Barry Irby

Thanks for posting that, its exactly what I am talking about. I have the cradle, not quit as pretty as theirs, But that's it.

I am just having a hard time getting the strips for the splines exactly the right thickness.

AND, I had not thought of angling the slots for the splines. Thanks for that tip.

Re: Splines on the corners of boxes????

#12

Re: Splines on the corners of boxes????

paul in AZ

I had also assumed that when splines were mentioned that he meant what I call keys.

I usually cut mine prior to assembly on the bandsaw. Fold each corner so that the outside faces are touching, exposing the miters; align all the edges and cut the slot. Easy to widen the cut for a larger key. That way it is easy to see how deep to cut and the cuts line up perfectly. Much safer than diddling around with jigs on the table saw. I also like the ability to make rather delicate looking keys for smaller boxes.

Re: Splines on the corners of boxes????

#13

Got it done....

Barry Irby

Cut them slightly too snug and then hand sanded them to fit. Glued them with Titebond II. About one per box I glued with medium CA because there was some very minor chip out on the slot and it makes good filler.

Thanks for all the help.

Got to send the blade in for sharpening. I remember this as being much easier. Just sawed the strips, glued them in and went on. I also suspect the slots as being very slightly variable. My only flat top blade is and ancient Sears blade I had when I was a kid. Shopping or a new rip blade to improve this job as well as ripping.