Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Live Edge Slabs, Hand-Selected in the Berkshires. Shop Unique Hardwood Pieces.

Tool to make wooden spoon bowls.

Posts

Tool to make wooden spoon bowls.

#1

Tool to make wooden spoon bowls.

Kay Cotton

I am an old retired hobby woodworker. I have been making wooden kitchen utensils for family. I have been using a chisel to rough form spoon bowls then sanding, sanding & sanding them smooth. Is there a router bit or something that would take the effort out of spoon making?

Re: Tool to make wooden spoon bowls.

#2

Re: Tool to make wooden spoon bowls.

Bob Hackett

I use a crooked knife to hollow and instead of sanding I use a scraper to smooth the bowl.

Re: Tool to make wooden spoon bowls.

#3

Re: Tool to make wooden spoon bowls.

Bruce, a MN Galoot

I just finished four spoons, and I used gouges (too small, need a bigger one) and a goose necked scraper. The scraper works particularly well. These spoons are big, so halfway through the project I got smart and chucked a forstner bit into the drill press and hogged out some of the middle of the bowl. That helped a lot.

Re: Tool to make wooden spoon bowls.

#4

Re: Tool to make wooden spoon bowls. *LINK*

Craig Daymon

I don't know if you are doing any turning to make your spoons, but in the July 2005 issue of More Woodturning magazine there is an article on making spoons by Doug Hartman that describes the piece he uses to hollow out the bowl of his spoons. It is basically an egg shaped (bowl shaped) piece turned on the end of a spindle that he mounts in the lathe. It is covered with cloth backed abrasive cut from belt sanding cut-offs. (Klingspor usually has boxes of cut-offs with various grits for reasonable prices.)

Doug makes wooden utensils for a living, so it might be worth seeing if you can get a copy of that issue. Fred Holder, who runs the magazine, offers PDF versions of the magazine and I suspect he has that issue still available. They have a CD of back issues. I didn't see specific issues available, but I would contact them and ask.

-Craig


More Woodturning Magazine

Re: Tool to make wooden spoon bowls.

#5

If you have something to spin it... *LINK*

John in NM

These burrs can be useful.

I use them in a Foredom tool, a Dremel will work for the smaller ones. Or you could maybe use them in a drill press or lathe and bring the carving to the burr instead of the other way around.


carbide burrs

Re: Tool to make wooden spoon bowls.

#6

Re: Tool to make wooden spoon bowls.

Kay Cotton

Thanks for the responses regarding the above. Much appreciated

Re: Tool to make wooden spoon bowls.

#7

Re: Tool to make wooden spoon bowls.

Pete in Holland MI

Saw a spoon guy in action one time.

Buy a 2" diameter drum sander. Mount in your drill press. Attach 60 grit sleeves to the drum, but let it extend below the drum about a half inch. Cut the "skirt" of the sleeve up to the rubber in about 8 places to make it conformable. Spin the drill press pretty fast.

Cradle your blank in your hands on the back lower side of the drum and pull it towards you into the drum.

He showed me how to do this. Takes him about 2 minutes to to rough out a spoon. Switches to 120 grit to finish it out. I did one in about 5 minutes.

Makes lots of dust, but once you learn the handling techiniques, works pretty well.

He used Cherry exclusively.

Re: Tool to make wooden spoon bowls.

#8

Re: Tool to make wooden spoon bowls.

eliot d

You can make them fairly easily on a lathe. If you have a lathe, let me know , and I'll explain the procedure.

Re: Tool to make wooden spoon bowls.

#9

Can you post the process?

Henry (Raleigh NC)

Eliot:

I have a lathe and would also like to try this. I don't see your e-mail for some reason.

Can you post the process? If you don't choose to, I understand completely.

Thanks

Henry

Re: Tool to make wooden spoon bowls.

#10

I'd like to see that process, too.

Bruce, a MN Galoot

And would it apply to spoons like these?


Re: Tool to make wooden spoon bowls.

#11

Re: Can you post the process?

eliot d

It's a bit difficult to give a precise step by step process. But the basic idea is to first turn a kind of holding cup for the eventual spoon. It would look something like an cylinder. Then you would cut a slit down one side of this cylinder that's a bit wider than the planned handle of the spoon. Next, you would turn what looks like a ball with shaft coming out of it -- kind of like a weapon with a ball at one end. The size of the ball is such that it can be pressed tightly into the cylinder that you just made. Now comes the harder part: you press the ball into the cylinder with the handle going through the slit you made. The cylinder/ holding cup with the handle sticking out through the slit is now mounted on the lathe. You now just turn a bowl into the ball. And yes, the handle that sticks out is spinning around and could give you a real whack if you're not careful! You also have to figure a way to bend the handle to something interesting. The only way I know is to wrap it in a wet towel and use a microwave. This process results in a kind of ladle. The method is for a fairly experienced turner. A much easier alternative is to just turn a small bowl and attach a handle afterwards, but that's not so elegant.( I suppose this is a clear as mud to some. Most turners will get it.)

Re: Tool to make wooden spoon bowls.

#12

Re: Can you post the process? *LINK*

Craig Daymon

I think most people would consider that a "scoop" rather than a "spoon". If large, like the size of the salad tongs shown, a "ladle".

If the idea is to make a more traditional wooden spoon, it is easy to turn the basic shape (aside from dealing with some vibration in the relatively long and narrow handle), given that turning the bowl end will involve turning air part of the time as it will only make up at most half of the bowl. I would use a forstner bit to drill a shallow recess where I want the bowl to be (before beginning turning). Once turning is complete, you will have to carve the bowl of the spoon.

You could turn the bowl, if rather than the traditional egg shaped bowl, you wanted a round bowl. Though, this would require a lathe with a good swing to turn a spoon of a traditional length.

Most wooden spoons have shallow bowls.

I posted a picture of a spoon I made for my sister recently (before completely finishing the bowl). Mine was turned from 3/4" thick stock, which I mounted slightly off center to give me more wood to carve out the bowl. It was far more than enough. I used rotary carvers. You could also carve the bowl by first turning a spindle, possibly with a morse taper on one end to push in the head stock, with an egg shape on one end. Cover that egg with adhesive backed abrasive (relatively coarse, maybe 80 grit) and spin that in the lathe, pressing the bowl region against the egg shape to carve out the bowl. I would still recommend starting with a forstner bit recess, which will make it easier to center and control the egg shaped sander and help lessen what needs to be carved.

Finish shaping the outside using a disk sander, which can easily be made out of a disk of plywood for the lathe. (One of our local turners turns/drills a recess in the back which he expands his chuck jaws into to hold it. Makes for a very compact design. He has 4 with different grits on each.)

Below is a link to a site dedicated to woodturning that has lots of articles on turning projects. The link is to their page for Spoons and Spatulas.


Woodturning Online Spoons and Spatulas

Re: Tool to make wooden spoon bowls.

#13

Re: Can you post the process? *LINK*

Craig Daymon

Here is a link, again from Woodturning Online, describing the procedure required (with photos!) to create Eliot D's spoon. Bowl size and handle length may be varied based on lathe size and desired spoon/scoop intended usage.

-Craig


Coffee Scoop with turned scoop bowl

Re: Tool to make wooden spoon bowls.

#14

Thanks Eliot and Craig - that helps alot

Henry (Raleigh NC)

Many thanks guys; I can visualize what to do, and how to do it!

Henry

Re: Tool to make wooden spoon bowls.

#15

Re: Can you post the process?

Kay Cotton

Thanks for the information, however, I think I better pass on the process. ;)