Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

Anybody using the current version of the Sears....

Posts

Anybody using the current version of the Sears....

#1

Anybody using the current version of the Sears....

Barry Irby

Contractor TS?

A friend is looking for a TS under a Grand and has looked at them. With various discounts he can get it for under $500.

It's a ten inch saw, has dust collection, riving knife, a Beis clone fence, rollers, 1 3/4hp continuous duty motor.

I have never even seen a picture of one so I have no clue. Wonder what the true hp of that motor is? Anybody got the skinny? (He has used an old Crapsman his father gave him for years and it had a half hp motor.)

Re: Anybody using the current version of the Sears....

#2

PS, Its the 21833 Model @ $598


Re: Anybody using the current version of the Sears....

#4

Re: Here's a pic with specs ...

Barry Irby

I got the cart before the horse and posted before I went a looked, thanks though.

There are "specs" and there is what really happens. Like many others, I am no longer a fan of Craftsman tools even though I still have a 45 years old RAS I bough when I was a kid and I like it. (I know, i know...insert boo's and snide remarks here, but this one is made better than the ones Sears sold since then)

I actually think my friend will be pretty happy with this saw. He has gotten along for many years with a old Craftsman saw that this father gave him and it had a 1/2 hp motor on it. It seems to me that he will perceive this as significant up grade. Also, on my recommendation he bought one of the Beis fences Lowes sold off for $80 a few years ago. He can install that on this saw if the fence it comes with proves to be crappy. I put one on my Delta Contractors saw and it was a significant up grade and I really like it.

So, I was curious if anyone had hands on experience?

Re: Anybody using the current version of the Sears....

#5

Re: Here's a pic with specs ...

Stuart Hough

Barry, I have the original version of this 3/4 cabinet style hybrid. Mine is the 22114, with the cast iron wings and 1.5 hp motor (pre-riving knife 2004 model). I have found mine to be a great saw for my needs, though I am admittedly still a neophyte. It cuts very well with my Freud blades. The original Craftsman blade did a serviceable job, though I did not keep it on for long. I will be shopping around for a higher-hp motor in the future, because my 1.5 hp unit has bogged down in some cuts I thought should have been no problem. I have talked with other owners of Craftsman saws with both the 1.5 and the 1.75 motors and we all have experienced the same thing (I'll admit it scares my wallet when I start thinking I've outgrown this saws power output!) For a first saw I believe this Craftsman saw will be a good choice for your friend, but I would DEFINITELY put an aftermarket fence on it. The OEM saw is ok for occasional work, but that's it. I frankensteined a Bies clone onto mine, and have been very satified with the performance. The saw cuts much better, and bogs less, due to the straighter cuts. Hope this helps.

Re: Anybody using the current version of the Sears....

#6

Re: I wouldn't recommend it

Charlie Lenz

If you look at the customer reviews on the saw you will notice quite a few complaints about blade alignment. I'd look for a used American made Contractor's table saw, such as Rockwell, Delta, Powermatic, or a JET, he allready has a good fence the way it sounds. And as I've said many times before, good dust collection on these saws is obtainable with the right dust hood under the saw.

Re: Anybody using the current version of the Sears....

#7

Re: Here's a pic with specs ... ( to Stuart )

Charlie Lenz

Your saws lack of power may just be what you have it pluged into. A machine with a motor any larger then 1 hp should really be pluged into a dedicated circuit.

Re: Anybody using the current version of the Sears....

#8

Re: I wouldn't recommend it

Steve Schoene

You have to expect to realign blades on any saw, though lightly built saws, as the Sears appears to be, don't hold alignment well.

The spec sheet posted above showed horsepower of 1 7/8 "maximum developed horsepower", which is usually about double the continuous horsepower ratings that are more appropriate. It's one of Sears long time tricks.

Especially since he already has a Bies fence he could transfer I would definately look among older used saws. You can definately get a bargain if you don't care about an obsolete fence.

Re: Anybody using the current version of the Sears....

#9

Re: I wouldn't recommend it

Charlie Lenz

( You have to expect to realign blades on any saw ) Not neccesarily true. I bought a Delta 34-445X Contractor's table saw new in 1995, and believe it or not, I've never had to realign the blade, it came aligned and has held alignment. The older used Rockwell Model 10 Contractor's table saw that I bought is a different story, it was so far out of alignment that I actually had to remove both Trunions and file out the holes, after all that I expect it to stay aligned. My main point in recommending a used American made machine is like the Delta / Rockwells, they made that saw for atleast 35 years, finding parts for it someday shouldn't ever be a problem for many years, also American made in most cases is alot better in quality then the cheap imports that are out there now, and I'm not just talking about the machine itself, the motors also. I also feel that American made machines hold their resale value better.

Re: Anybody using the current version of the Sears....

#10

I reported everyone's comments to my friend

Barry Irby

He has decided to buy it today and has accumulated a number of discounts and expect to pay about $450 for it. He has work experience setting up and tuning machines and expects to get it set up and tweaked without too much cursing.

The Beis fence he has has never been installed, its one of the ones Lowe's sold at deep discounts a few years ago. (I tipped him off and he snagged one and has been saving it.)

I will report back on his level of satisfaction.