Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

Windsor chairs

Posts

Windsor chairs

#1

Windsor chairs

Joseph Mulherin

Found a website showing several different writing table chairs.

Gregory LeFever is making many of the designs shown at

www.Early American Life.com/October 2008 issue

Am thinking I shall be producing a few for myself and family members

Re: Windsor chairs

#2

Re: Windsor chairs

Joseph Mulherin

Follow up: Gregory is a writer of the article. If you are interested in learning about making some Windsor chairs go to: Mike Dunbar at TheWindsorInstitute.com in Hampton, NH.

Re: Windsor chairs

#3

JL

Re: Windsor chairs *LINK*

JL

There are other alternatives (see link)

Also Curtis Buchanan and Brian Cunfer http://www.pachairmaker.com/events_classes.htm


Windsor chair instructors

Re: Windsor chairs

#4

Re: Windsor chairs

Philip Duffy

And, don't forget the Dean of Windsors, Peter H. Wallace- - -windsor-chairs.com---. His chairs are repos of the originals and fantastic to see and to sit in! He has a chair in the permanent White House collection. Philip

Re: Windsor chairs

#5

Re: Windsor chairs

Joseph Mulherin

Have watched several makers of the chairs and their methods, but I am planning on using my Shopsmith 5in1 tool to make the various parts. First i am going to make some 1/4" patterns to place on my "duplicator" so I get the exact sizing on the turnings, etc. Scorping out the seat is going to be something else, but earlier in the year I found a seat making method using the router and some curved shaped boards. Steambending box I am going to have to build too.

Is going to be a large change from my earlier woodworking, but i do need the experience and the enjoyment of shaping the wood to my desires and needs to make a very good present for my friends and family members.

Re: Windsor chairs

#6

Re: Windsor chairs

Barry Irby

I am no expert on making seats, but I have made a few. Did not own a S Corp and thought I was only making one seat, so did not buy one. On the first one, I use my radial arm saw as an overhead "router' (?) and clamped the workpiece to the table and lowered the blade about a 1/16" at a time, cutting at ninety degrees to the normal direction of cut, sort of like you cut coves on a TS. Then I sanded it into submission with my ROS. (It was a Wild Man Method and it worked, but I was not willing to do it again and would not recommend it.)

What worked much better was to draw a "topo" map on the seat and use a forstner bit to hog away a lot for the material. Drilled about a 1/4" deep young the perimeter. Then stepped in and drill about 1/2" deep in the center. (these were very small seats and the saddle was for a baby's butt.) You could use a third step if you needed to. Then I put a very coarse 4" sanding disk on an angle grinder and finished sculpting it by eye. I sued the disk alone, without a backer and did two small seats with one disk. These were small seats, about 12 by 12" and I did the final shaping in about 45 minutes to an hour. Used the pilot holes left by the forstner bit as depth indicators. That went much better and was easier than I expected. I set the hose from my dust collector and nearby as I could and wore a dust mask.

Re: Windsor chairs

#7

Re: Windsor chairs Seat Carving

Paul Leuba

There are many ways to tackle this task, and most of them will yield a very attractive seat profile.

The method I learned, and still use, makes use of a gutter adze to rough out the saddle, followed by a #7 gouge to refine the profile and then finished with a random orbital sander starting with 80 grit to smooth it.

I find that the profile that looks best for me and is most comfortable, carved in a 2" thick seat blank, is approximately 1 - 1 1/4" deep in the rear with adequate reflief for each leg, leaving a raised portion separating the legs in the front.

By using hand tools, mostly, I believe it is more difficult to make a costly mistake that ruins a seat blank. And, the hand sculpted profiles look great and feel great to sit on.

Most of the fun for me in crafting a Windsor chair is in sculpting the saddle.

Paul in Hunt Valley, MD

Re: Windsor chairs

#8

Re: Windsor chairs

Joseph Mulherin

Barry, I like the idea of using the Fortsner bits to drill to various depths and then carve out the remaining barriers....shall give it a try on a scrap piece first to work out any flaws in working I will probably run into. Then shall try to use my belt sander and ROS to finish out. Will let you know how it turns out.

Re: Windsor chairs

#9

Re: Windsor chairs

Barry Irby

The ROS worked well, but one the first one I sued it for stock removal and the bearings gave out. Part of that was age and general wear, but I think I dogged it to death on the seat. The Angle grinder was much faster and was not bothered at all by the sculpting. I borrowed the one I used and it was pretty nearly shot when I started. If I were to do this again, I would buy one of my own, even if it were from Harbor Freight.

I did do the final sanding with a ROS and that went well, but I used a much lighter touch.

Re: Windsor chairs

#10

JL

Mechanical carving of seats

JL

I have a set of the tungsten carbide "donuts" for my angle grinder. They work well on the harder woods (cherry, white oak, etc.). I also have a "Lancelot" chainsaw grinder that I use for the harder woods.

When I use softer woods, I start out with the gutter adze and my scorp. I finish with my angle grinder using 24 and 36 grit sandpaper.

For both I finish with my ROS and progressive grits of sandpaper.

I usually just do depth holes across the rear of the seat portion in front of the spindle deck. Usually two on each side of my center line. I leave the pommel of the seat around the center line alone and carve down from there.

Re: Windsor chairs

#11

Re: Mechanical carving of seats

Joseph Mulherin

Yes, JL, that is what I intended to try to do when I make my first chair.

A couple years ago I tried to make the Western chairs they show in the movies at the saloons, but never finished it and just cut it up and trashed...but the same idea would work for making the seats of the Windsors.