Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

6 V vs. 12 V lamp wattage

Posts

6 V vs. 12 V lamp wattage

#1

6 V vs. 12 V lamp wattage

Al Stokka - Cambridge, Iowa

Howdy,

I need help comverting a light bulb. The application doesn't matter. Well, OK, it's a proofmeter (combination tachometer, speedometer, and hour meter) for a tractor. 8N Ford tractor to be exact.

The replacement tachometer came equipped with a 12 Vdc, 2 watt lamp for backlighing the face of the tach. My tractor, being the PROPER 6 Vdc, will not light the 12 V lamp properly (I assume. I haven't tried it and don't intend to until I change the lamp.) so, I need to know what wattage 6 Vdc lamp will produce the same light output as a 2 Watt, 12 Vdc lamp?

I don't want to use too high a wattage lamp because I fearful of the extra heat buildup in the tach enclosure, but I don't want too low a wattage lamp and rish note being able to read the tach.

If you'd care to share the formula, that would be a plus and I'll attempt to remember the formula but, at my age I won't make any promises. ;^)

Al

Re: 6 V vs. 12 V lamp wattage

#2

Re: 6 V vs. 12 V lamp wattage

Pete in Holland MI

Al -

Plug it in with a 6 volt charger in a dark garage and see what you'll get. It won't be bright, but it will glow well.

I put an indicator bulb (small clearance light) on my dad's jubilee with a 12 volt bulb on a 6 volt system, and it is still visible in the daylight.

Also.......are you familliar with www.yesterdaystractor.com? There's a Ford and Ford N forum on there with lots of guys to help you out on further questions. I hang around that site a lot !

Pete

Re: 6 V vs. 12 V lamp wattage

#3

Re: 6 V vs. 12 V lamp wattage

Dave Peebles Lyons, Ohio

Hi Pete,

Don't mean to highjack the tread, but I just sold my Jubilee about a month ago. I hated to do it, but I knew I would never have the money or time to do a proper restore. It really hurt to let it go, but it went to a great guy who has done many restorations. I feel it is in good hands.

Dave

Re: 6 V vs. 12 V lamp wattage

#4

Re: 6 V vs. 12 V lamp wattage

Bill Tindall

power= watts = I^2R = EI where I is current, E is voltage and R resistance. However a 5 watt light at 12 volts puts out the same light as a 5 watt light at 120 volts. The resistance of the filament is adjusted to the voltage for the lamp to yield the same watts. The same watts heats the filament the same yielding the same filament temperature and same light.

that said, a 12 V lamp will likely work just fine with a 6V system. It just may be a bit dimmer. I power our Christmas lights off a variable transformer at 40 volts. They are a bit dimmer but last forever.

Re: 6 V vs. 12 V lamp wattage

#5

Re: 6 V vs. 12 V lamp wattage

John McGaw

To answer directly the question asked, a 2W 12V bulb will put out the same light as a 2W 6V bulb or for that matter a 2W 120V bulb. The key is the 2W which indicates the amount of power being consumed and turned into heat.

Re: 6 V vs. 12 V lamp wattage

#6

Thanks!

Al Stokka - Cambridge, Iowa

Thanks guys. I guess I should have asked earlier. Not much hope of finding an auto parts store open on thanksgiving. sigh.

Y'all have a great day and try not to eat too much...NOT!

Al

Re: 6 V vs. 12 V lamp wattage

#7

Re: 6 V vs. 12 V lamp wattage

Al Stokka - Cambridge, Iowa

Pete,

Yup, Yesterday's Tractors is the site I visit every day...right after I catch up on Wood Central. I don't post much, but enjoy reading everything.

Al

Re: 6 V vs. 12 V lamp wattage

#8

Re: Thanks!

John McGaw

I was going to say that somebody down on the Interstate probably has them and will be open but then I realized that 6V bulbs have become a real rarity. I wonder if your average auto parts store will even have them in stock.

Re: 6 V vs. 12 V lamp wattage

#9

Re: Thanks!

Bill Turpin in WNC mountains

I think that a 4w/12 volt bulb fired with 6 volt will give the same light. There is a "squared factor" floating around in there somewhere. Light bulbs are a special case because they are current limiters after the filament starts to glow. Otherwise the filament would melt the first time used.

Re: 6 V vs. 12 V lamp wattage

#10

Re: Thanks!

Jerry Nicholson

No - the 4W 12 volt bulb will be dim and yellow on 6 v, just like any 12 volt bulb will be.

Jerry

Re: 6 V vs. 12 V lamp wattage

#11

Re: Thanks!

John McGaw

If you halve the voltage then you will dissipate 1/4 the power, at least in a purely resistive circuit, since the current drops by 1/2 and the voltage drops by half and power = voltage times current. As you say, the tungsten filaments in a bulb are a bit quirky in that their resistance varies with their temperature but it does so in a way which suggests that they should self destruct when power is first applied -- the cold resistance is low and the hot resistance is high and the ratio is usually more than 1:10. Luckily the resistance shoots up rapidly when power is applied so they self-protect pretty well when in good condition but this is the reason that bulbs most often fail when they are first switched on.

The trivia we pick up over the years... :)

Re: 6 V vs. 12 V lamp wattage

#12

Speaking of trivia...

Bill Houghton, Sebastopol, CA

...and they fail, generally, by burning through at one connection point to the terminals bringing them the current, leaving the filament waving about in the breeze. Striking the fixture with the bulb in it a firm, padded blow - say, what you'd get by whapping it with an open palm - while the power is on can sometimes cause the filament to vibrate back into contact with the terminal, where high resistance will cause the filament to arc-weld back in place. It's a weaker connection, so it won't last forever, but it can get you a bit more use.

I learned this back in my motorcycling days, when headlights were customarily 6V or (rarely) 12V bulbs, rather than the sealed beams that came in later. I decided to test the idea, so when the bulb blew out on my BMW, I whapped the headlight nacelle - and it worked! I went out and bought a replacement bulb, wrapped it in cloth, and stored it for the time when the bulb failed altogether; but I got an extra six months from the "broken" bulb by whapping the headlight every time I started the bike (I always ran with headlight on for safety) before I got tired of whapping the headlight and replaced the bulb. If I recall correctly, it took me about a week to remember NOT to whap the headlight upon startup, but I was younger then. Now, if I still rode, it would take me six months.

Filaments on household light bulbs seem to fail rather more explosively, so I'm dubious this would work in a household bulb