Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

Checkering . . . ?

Posts

Checkering . . . ?

#1

Checkering . . . ?

steve mackay

When I make my "diamond" pattern "decking" on models I use a gent's saw to score then "define" it with a swiss pattern file. The thought occured to me this afternoon that it is similar to "checkering" on a gun stock. I looked at a couple videos on line and looked at the tool. Question is : This is done on hardwood. Would a checkering tool work on my soft wood ? Or do you think it would just tear it up when cutting cross grain ?

Re: Checkering . . . ?

#2

Yes it will work

Ray - Middletown, IN

Get a fine tooth cutter, they come in different tooth counts, just use a finer cutter. Or just go lightly. :)

Ray

Re: Checkering . . . ?

#3

I can lend you a couple tools...

John in NM

I would want them back of course, but you could try it out before spending the $$

I think mine are 22 tpi, which may be a bit coarse for your needs, depends on the scale of the model.

Re: Checkering . . . ?

#4

will work, just not well

Don Evans

There are fine and there are course cutters but that has nothing to do with the TPI that you are checking.

When checking you start with the course cutter going very light, then you switch to the fine cutter to continue to the proper depth of the line you are cutting.

The number of teeth on all the cutter is the same on the course and the number of teeth are the same on all the fine cutters.

Where the tpi comes in is due to special cutters that make more than one line at the time, for example I have double line cutters and triple line cutters how far apart the double line cutter are from each other is what determines the tpi you are cutting.

DemBart which is all I recommend makes cutters spaced from 16 tpi to 24 tpi.

It ain't got nothing to do with the number of teeth.

Soft wood will not work well even with the fine cutters. You can of course do it, it just will not be as pretty and smooth as the hardwoods.

Don

Re: Checkering . . . ?

#5

Re: Checkering . . . ?

Philip Duffy

Checkering is done after the finish is in/on the wood so that is a key factor in the cleanliness of the lines, diamonds, etc. Not so sure soft woods would take the sharpness of clean edges. Give it a try and tell the WC world. Phil

Re: Checkering . . . ?

#6

Re: I can lend you a couple tools...

steve mackay

Thank you. But I just KNOW if I HAD a tool that it'd get use on hard wood as well. Useing it for the models is going to be my excuse for getting one. :D

Re: Checkering . . . ?

#7

Danke . . .

steve mackay

Sounds like we'll give it a try. Compared to cutting parrallel lines my way this might speed the proccess. Thats always a goo thing. Of course if the tool were in the house I can see this "checkering" thing getting out of hand once we got good at it.

Re: Checkering . . . ?

#8

I know how that goes

John in NM

Should work just fine on soft wood, it's basically just a more convenient tool to do what you're already doing with the file.

Be careful though, there's also a really expensive power version to tempt you :D

Re: Checkering . . . ?

#9

Re: Checkering . . . ?

TomD

Yeah they are designed for hardwood. They will work on softwood to the extent that anything does. It would be like filing with a triangular file. I don't know who has them in Canada, I could ask for you on Gunutz, if you aren't a member. You may want two relatively cheap tools, the cutter, which is sold on a line per inch basis, and a jointer, which is a longer single that allows one to straighten runs if they start going off line. I have the two tools, and am just down the road, but I haven't seen then in a decade. If you actually wanted a grip type thing, you could use a stippling tools. Another option is one of those air tools that breaks off the slag.

I think the answer on gun tools is that everyone up here uses Brownells. They have a huge catalog. While getting parts up to Canada is becoming more nightmarish all the time, the tools are not a problem. Brownells still deals with Canadians, many outfits that sell gun stuff will not deal with us at all, even to send us stuff in no way gun related.

http://www.brownells.com/.aspx/pid=6780/Product/GUNLINE-JOINTER

I didn't see the tool I bought in there, it uses small interchangeable heads, and was cheap. Must be in there since the heads are available.