Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A natural, durable finish with minimal coats and fuss popular among woodworkers, flooring professionals, and furniture makers

OT - Making a simple LED circuit

Posts

OT - Making a simple LED circuit

#1

OT - Making a simple LED circuit

Ray Carson - Lawrenceville, NJ

Okay, so I've been researcing this subject for a couple of days now. Someone asked me to build a particular project with a LED light. I've been to Radio Shack and have already purchased some of the items. Here's what I have so far:

(1) CR2032 battery holder

(1) CR2032 battery - 3v

(1) 5mm White LED

High visibility, 5mm Round T-1 3/4

Intensity 7000mcd (typical);viewing angle 30°

FW current 25mA; FW supply 3.3 (typical),

3.6V (maximum)

(1) roll of 24 ga. two lead wire

(1) micro push button switch

My question is whether or not I need a resistor and of what size. Everything I'm reading says I need one or the LED will burn out because of the rate at which the power is being delivered. The guy at the RS store says I do not need one and says the CR2032 will power the LED straight forward. When asked if and when the LED burns out if I hook it up this way, can I return the LED for a refund or will they replace the LED at no cost. ;)

Please help.....

Ray

Re: OT - Making a simple LED circuit

#2

Re: OT - Making a simple LED circuit

John McGaw

Typically an LED circuit needs some method of current limiting. This is most commonly a resistor but sometimes an active electronic circuit is applicable. In your example there is a great chance that the LED is not going to light no matter what you do. You see, you need to have a voltage source greater than the forward drop of the LED. In your case, assuming that I'm reading the specs you gave correctly, the forward drop of the LED will be 3.3V so your 3V source will not make it conduct at all.

Assuming as an example a voltage source of 6V (two batteries in series) you would need a resistor of 108 Ohms so the closest standard resistor value of 110 Ohms would be appropriate. White LEDs are somewhat peculiar since they don't actually generate white light directly. Instead they emit light at the long end of the UV spectrum (giving them a peculiarly high band-gap voltage) and the UV activates phosphors to give the desired quality of white light. This is almost exactly the same mechanism that your regular old fluorescent bulb uses.

Had you been using an infra-red or red or orange or yellow or green or some blue LEDs 3V would have been sufficient for your purpose.

Re: OT - Making a simple LED circuit

#3

Re: OT - Making a simple LED circuit

del schisler

the led voltage 3.3volt You will not need a resistor to drop the voltage . the led is 3.3 volt. and the cr2032 battery is 3 volt. that will be fine. i been in repair for 50 yrs and that will be fine as far voltage goes. Now hook it up with pos to pos or it will not lite. they have to be pos to pos.

Re: OT - Making a simple LED circuit

#4

Shouldn't need the resistor

John in NM

My understanding is that the internal resistance of the battery acts as the current limiter, so an additional resistor is not needed. Bear in mind though, all my fooling around with electronics was 20 years ago :D

Re: OT - Making a simple LED circuit

#5

Instructables *LINK*

Tom Dunlap

Electronics are over the horizon for me. Given parts and a diagram I guess that I can assemble but I would have no clue what is happening.

Go to:

http://www.instructables.com/

and poke around. There are lots of LED projects there. You'll find someone who has built what you have in front of you or they would be able to give you a definitive answer


Instructables

Re: OT - Making a simple LED circuit

#6

Re:response from del

Ray Carson - Lawrenceville, NJ

del,

I figured I'd take my chances since the LED is somewaht cheap, so I tapped the correct leads of the LED to the battery. Works fine. You and the sales person at RS are correct. Thanks. The only time you need a resistor is if the supply is greater than the LED can take....I think.

Do you know how to determine the ohm capacity needed for circuits?

Thanks,

Ray

Re: OT - Making a simple LED circuit

#7

Re: Instructables response from Tom

Ray Carson - Lawrenceville, NJ

Tom,

Thanks for the LINK. I actually found that website while researching and signed up. I'm like you, not great with electrical stuff but give me everything I need and a diagram and it's shocking what I can accomplish. (pun intended)

Ray

Re: OT - Making a simple LED circuit

#8

Re:response from del

John McGaw

I think that there is some misunderstanding here. An LED has no voltage limitations in the forward-biased state, it has a current limit. Once there is enough voltage applied it will conduct (for all intents and purposes) as much as the source can supply. The key is that the voltage drop, 3.3V in the case of the LED you wrote about, is essentially constant once the LED starts conducting. This willingness to 'conduct itself to death' is the reason current limiting is required. Since your LED lit at all and didn't damage itself means that the forward voltage spec is wrong or that the CR2032 is putting out more voltage, at least momentarily, than it is specified for and that the battery is not capable of putting out much current (this type is designed for a 0.2MA standard load).

I'm assuming that you don't have any sort of test equipment but one way to make sure is to forget about 'tapping' the connection and simply connect it and watch what happens. The CR2032 is rated to put out only a couple of MA so it probably can't put out enough to damage the LED no matter what. How long the LED is willing to stay lit will tell you how well the setup will work -- unless the final application calls for short flashes of light.

BTW, calculating the current limiting resistor in a generic way is pretty simple:

(supply voltage - LED forward voltage) / desired current

example

6V battery - 3.3V LED FW voltage = 2.7V

2.7V / 0.025A = 108 Ohms and the closest standard value to this is 110

Re: OT - Making a simple LED circuit

#9

Re:response from John

Ray Carson - Lawrenceville, NJ

I'm going to use (4) - LR44 button cells in an A23 battery holder. This is 6V. So a 110 ohm resistor should work, right?

Ray

Re: OT - Making a simple LED circuit

#10

Re:response from John

John McGaw

Yep. At least that is what my calculation and several decades of experience tells me. Since the alkaline LR44 is rated at 150mAH you'd think that the LED should work for 6 hours but the hidden catch is that this cell is designed for a much lower load than the 25mA that the 110 Ohm resistor would allow so I'd be very surprised if the light lasted for more than an hour. One option would be to increase the resistor value to reduce the current (and light) or to use larger batteries but most of the little button or coin cells are meant for the long haul with light loads so getting a long life would call for a still larger power source. Probably the best thing to do is to try it out and adjust the resistor value to try to get enough light to do the job for as long as you can.