Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

game table hinges

Posts

game table hinges

#1

HapaJeff

game table hinges

HapaJeff

I have an unusual situation that I'm looking for a solution for. I'm changing the hinges on an antique game table. At some point in the past, some yahoo changed out the hinges, only to use a Soss-type hinge, which is not only inaccurate, but looks out of place as well. Here's the kicker for me: the table doesn't have straight sides. "Normal" game tables are rectangular when closed, and square when opened; at least they're straight where the two halves come together. This table has an undulating side. I've attached a sketch for clarification.


There are two solutions that come to mind, but I'm hoping that you might have something simpler. One solution is to bend the arms of the hinges to match the curve of the table. Honestly, this operation seems like there's a high likelihood of distorting the hinge to the point that it doesn't work. The second solution that I thought of was to cut a mortice into the side of the table to allow the hinges to work in one plane, and then plug the mortice to hide it. The problem here is that if the hinges ever need to be tightened or removed, I'll have to dig them out.

For reference, I purchased a pair of these hinges: http://www.whitechapel-ltd.com/product/cardh/244H31.html


Any ideas for me?

Thanks,

Jeff

Re: game table hinges

#2

Moses Yoder

Re: game table hinges

Moses Yoder

It looks to me like anything you do on the ends of that table is going to look much worse than a properly fitted SOSS hinge, about 3 spaced a couple inches from the edge and one in the center.

Re: game table hinges

#3

Ellis Walentine

How much curvature is there?

Ellis Walentine

Hello Jeff,

You're worried about curving the blades of the hinges, but how likely is that to actually impede the action of the hinges? Maybe it would make sense to mock it up and see if your worries are founded.

Is your concern with the invisible hinges (Soss) that they detract from the table's antique value?

Ellis Walentine, Host

Re: game table hinges

#4

Look up Sewing machine hinge

Ketih Newton

They are visible from the top when open, but are not bad looking.

I have a bunch left over from a project years ago, where it was cheaper to order a box of 50 than however many I needed. There are two brass leaves, with two pins, through a third middle piece.

Re: game table hinges

#5

HapaJeff

Re: How much curvature is there?

HapaJeff

Ah, good questions.

The hinges' leaves are about 2 9/16" long (5 1/8" when opened). I would have to bend each leaf about 5/16" to match the curve of the table.

The Soss hinges that were installed are aesthetically displeasing and don't fit the age of the table. While they do work well, they are inappropriate for the table. My client wants them replaced because they look so badly.

Re: game table hinges

#6

HapaJeff

Re: Look up Sewing machine hinge

HapaJeff

I looked at sewing machine-type hinges, but, when looking at this antique, I could find no evidence that they were used originally.

Re: game table hinges

#7

Re: game table hinges *LINK*

Mark Mandell - Gone Round In Jersey

If you look closely at the third panel of the link, you will see that the hinges you have now are the correct ones and where/how they are to be mounted.


table

Re: game table hinges

#8

Re: game table hinges

Ketih Newton

Hapa, Looks like you and Mark are right. You shouldn't have any trouble bending those hinges, just try to keep that middle part straight, and perpendicular to the joint. You can bend anything you want outside of the first screw each way.