WE MOVED...
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Table Saw Fence Recommendations

Posts

Table Saw Fence Recommendations

#1

Table Saw Fence Recommendations

Steven P. Bellner

I know this topic has been discussed at length before, but I have not seen any comments on the (relatively) new Incra LS series of rip fences.

My 60's-style tubular stock fence took a dirt-nap yesterday, and I am now looking to upgrade. I have always been unhappy with the OEM fence, but it worked, and I put up with all its problems. At one time I looked at the Biesemeyer and unifences, but it appears Delta has acquired Biesemeyer and I'm not sure there's much difference between them in terms of basic functionality. There is also the Vega that gets rave reviews. These all seem to be the "T-square" style fence.

Then there is the Incra-style that uses the indexing method made famous in their router add-ons. I have some Incra products, and I am impressed with the fit-and-finish in addition to the performance of their intended function.

It probably comes down to personal preference, but does anyone have experience with the LS-style fence? This has apparently replaced their saw-tooth style fence. Is the Incra so superior to the others it is worth dropping another two bills to move to the Incra style?

I have a contractor saw, but it isn't the junk being pawned off as table saws these days. All cast iron, adjustable trunnions, has a link-belt driven induction motor. It has served me well for dozens of years, and I know a decent fence probably will cost close to what I originally paid for the whole saw, but in my opinion, the fence is what makes the saw, so I'm not averse to spending a little extra for a high-quality fence. FWIW, I'm a serious hobbyist, not a production woodworker, so accuracy is more important to me than ease-of-use or ruggedness, although I would expect any decent product to be fairly durable.

Re: Table Saw Fence Recommendations

#2

Re: Delta T2 Fence

Charlie Lenz

The Delta T2 fence is probably the best bang for your buck at around $150 the last time I checked, and would probably be an easy bolt up to your saw.

Re: Table Saw Fence Recommendations

#3

Re: Table Saw Fence Recommendations

Barry Irby

I can't answer your specific question, but that has never stopped me before, so here goes.

A few years ago I bought one of the Biesemeyer fences at Lowe's on close out. I also have an older Contractors saw, In my case, 40 years old and I could not bring myself to put a $400 fence on a $350 saw. But, when they went on sale for $80, I grabbed one. (Delayed Gloat) I couldn't be happier. I have upgraded the wings, the motor and the pulley and belt and now the fence. I am pretty happy with the saw and can see no short coming that would cause me to upgrade.

I would recommend the Beis fence. (But then I got mine cheap). Actually, I would recommend it even if I had paid full price.

Re: Table Saw Fence Recommendations

#4

Re: Table Saw Fence Recommendations

Dave in Bryn Mawr PA

VEGA is my third fence and the one I will keep for life! Easy adjustment of fence squareness, micro adjust, firm fence lock. Amen

Re: Table Saw Fence Recommendations

#5

Re: Table Saw Fence Recommendations

Bob in NE Ohio

Steve

I have had a TS for about 12 years. I put it originally on a Grizzly Contractor Saw and It worked like a charm. When I bought my Cabinet saw about 4 years ago I moved the TS and did not even install the one that came with the saw. I would not trade it for any other that I have seen. Cost a little more but the accuracy and repeatability are second to none.

Just my 2 cents worth.

Bob

Re: Table Saw Fence Recommendations

#6

Re: Table Saw Fence Recommendations

Larry Clinton At Frankfort, (Central) Indiana

Steven, I too have several Incra tools & fixtures including the 3000 miter with sliding table (think its now sold as a 5000 something). I have Delta Unisaw with the Bessy fence. As far as I'm concerned there is nothing I could gain by installing a Incra fence on my saw. I can sight in the fence using the scale to within less than a 1/32" on the first try (usually much closer). If needed I can cut a piece of scrap, measure it and reset to within .005" easily using digital calipers. I really can't think of any reason to need more accuracy than that for ripping operations. I really don't use the Incra table /fixture often, only for very accurate angles or when cutting tenons. Normally I use my home built crosscut slide table. (Quicker to grab and use). The Bessy fence holds adjustment perfectly, its is quite easy to align and set the tension on the release, and once set holds for years in my use.

Re: Table Saw Fence Recommendations

#7

Re: Table Saw Fence Recommendations

Dave Peebles Lyons, Ohio

Hi Steven,

I have a few of the Incra tools. They have worked great for me. I am not familar with the fences for tablesaws. But I am with Dave in Bryn Mawr PA on the Vega fence.

I added one to my old Sears/Craftsman saw. It was the best money I ever spent on an upgrade to a tool. It has worked beautifuly for 15 year. When I first bought it I pulled out the tape measure to check it. After a short time I left the tape measure on the bench. It was dead solid perfect every time.

I also had a hard time paying more for the fence than the saw was worth at the time. But it turned an inexpensive saw into a very accurate ripping machine. :)

Dave

Re: Table Saw Fence Recommendations

#8

Re: Table Saw Fence Recommendations

Dave Paine

I have an Incra Router fence which I love. Also have two Incra mitre gauges which I use whenever I need to mitre. Accurate and repeatable.

I considered the Incra Table Saw equivalent, but two reasons stopped me from purchasing :

a) I did not have the space to the right of my table saw for the track body. Other tools are in the way.

b) I did not see how I could use the fence to cut to the left of the blade which I sometimes need to do. Not often, but I have been glad when I needed to do so.

I have a Delta Unisaw with Bies. fence. This replaced a hybrid saw which also have Bies fence. I am very happy with the present fence and was also happy with the version on my earlier saw.

The one feature I would love from the Incra Jointer fence is the multiple rules. Makes it very easy to zero out then move the fence the width of the next cut.

Re: Table Saw Fence Recommendations

#9

Re: Table Saw Fence Recommendations

Charlie Lenz

Well if we are going to talk about high end table saw fences, the Unifence also deserves a look. I've been useing one on my contractor's table saw since I bought the saw new in 1995 and I'm still very happy with it. I'd put it up against a Biesemeyer anyday.

Re: Table Saw Fence Recommendations

#10

Does anybody know.....

Terry Alexander

....if the Delta T2 fence will fit on my Delta 36-650 contractor's saw? I LOVE my contractor's saw....but I still have the original fence.

As always.....thanks in advance!

Terry Alexander in West Texas

Re: Table Saw Fence Recommendations

#11

Jim DeLaney, Austintown, Ohio

Re: Biesemeier Home Shop Fence

Jim DeLaney, Austintown, Ohio

I had one of these on my 1970's Craftsman saw for about ten years, and really liked it. It's essentially a slightly lighter version of the 'regular' fence. The tubing the fence slides on is slightly smaller, and the fence itself is about an inch lower than the 'standard Biese, but other than that, they're the same.

When I upgraded to a cabinet saw, about ten years ago, I sold the Craftsman, with the fence, and as far as I know, the 'new' owner is still using it.

Re: Table Saw Fence Recommendations

#12

Re: Does anybody know.....

Charlie Lenz

Terry, as far as I know, the T2 should be a fairly easy bolt up. I also think that the customer reviews in Amazon.com are pretty good, perhaps someone there has bolted one to their same model of Delta as you have and wrote about it. I'm also wondering if your model of saw was sold with an optional T2 fence. Gotta luv the internet, theres alot of info out there.