Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

Drawer slips

Posts

Drawer slips

#1

Drawer slips

Bill Tindall



Drawer slips are a feature of every English drawer I have ever seen in antique stores. English drawers tend to be made from thinner stock than American drawers. The slip provides three functions. It provides additional bearing surface for a drawer with thin sides. This function could be useful on a large drawer. The slip provides the groove into which the drawer bottom is "slipped", without weakening the thin drawer side with this groove. And finally, the slip makes an easy task of aligning the grooves for the drawer bottom. Additionally, the "slipped" drawer looks attractive from the inside.

There are all sorts of variations on the slip. What is shown in the picture is an example that is easy to make and install. I make the slip from scraps of wood such as the piece that has not yet been cut to size shown in the center of Picture 1. Slips are made about 1/2" thick. If the scrap is wide enough two slips can be cut from one piece of wood, which is efficient, is in the case shown.

In Picture 1 we can see the notch that is removed from the back of the slip. Its depth is made so that the top of the groove aligns with the bottom of the drawer back, allowing the drawer bottom to be slipped in from the back of the drawer. The slip groove is aligned with the groove in the drawer front by employing a piece of wood the exact thickness that the groove is wide, as seen in Pictures 1 and 2.

After fitting the slip is glued in place. A rub joint is sufficient if the mating of the slip and drawer side is precise. If not, clamp for a few minutes.

The slip width is sized so that its edge falls below the fitted drawer bottom. What ever part of the slip sticks past the drawer side bottom is planed off so that the bottom of the slip and the bottom of the drawer are even.

I didn't invent any of these techniques. Rather, they have been adapted from other's work and suggestions, as well as studying English furniture.

Re: Drawer slips

#2

Re: Drawer slips

Barry Irby

Bill, this is something I am not familiar with. I don't understand the the concept. I grew up with antique furniture that my grand mother acquired and it was probably locally built in and around Virginia. I doubt any of it was English.

Can you explain the idea a bit better to someone who has no clew as to what a slip is? Is this a sturdy frame around the bottom of a drawer made of very thin stock?

Re: Drawer slips

#3

Re: Drawer slips

Bill Tindall

Picture 1. the left vertical is the drawer front, the right vertical the drawer back. The slip is the piece with the groove and quarter round profile.

Picture 2 the piece of poplar with the dovetails on the end is the gauge block for aligning the slip groove with the drawer font grooves. The drawer bottom slips into this groove.

Re: Drawer slips

#4

In addition, Barry...

David Yoho

The front is grooved since it's thicker than the other three parts. Using thin stock for the sides and back means there's not much meat left where the drawer bottom groove goes. The slips do two things - first, they provide the groove for the bottom without cutting the thin sides (no need for a groove on the back in order to slide the bottom in), and second, it adds thickness to the sides allowing for longer wear when no mechanical slides are used, which would have been the case back then.

Re: Drawer slips

#5

OK, so what is the advantage????

Barry Irby

As I see it this allows for the use of very thin stock for the drawers. lets say 5/16 or 3/8" but require the making and installing of the slips. Assuming you had an adequate supply of thicker material, the drawers seem like they would be made of fewer pieces but perhaps more material. The slips would give you the ability to use thinner material but with more pieces and some of them out of more substantial stock. Did I get that right?

It does seem that if you let the slip project beyond the side of the box you would have wear surfaces of both the side and bottom on the slip and it would be easy to tune the drawer.

Re: Drawer slips

#6

drawer fitting

Bill Tindall


The slip provides no benefit to drawer fitting. The fit is determined by the space between the drawer front and the drawer frame surrounding the front. Ideally the total gap here on fine furniture is about 1/16" total. I make the front to just fit this space. After the drawer is assembled it is fit to the opening by planing the sides. The drawer is held for planing by slipping it over a piece of plywood as shown.

Bottom line-slips enable thin drawer sides. Thin drawer sides look better on fine furniture.

Re: Drawer slips

#7

Re: Drawer slips

doug f, san clemente, ca

Bill - I must admit that I have never used drawer slips and am completely unfamiliar with the concept. Am I correct that the slip is an extension of the drawer sides and actually rides on the cabinet frame? If it is, how is it attached to the drawer side and when is the groove cut for the drawer bottom?

I typically use maple for drawer sides, 3/8 to 1/2" depending on size and have not had a problem with wear; but then most of my projects have only been around 30 years or so and haven't been subjected to really hard use.

Please forgive the naive questions but I am intrigued by a new technique (to me) and am eager to learn from someone who has extensive experience with it.

Thanks for your help.

Doug

Re: Drawer slips

#8

Re: Drawer slips

Bob Hackett

Extensive discussions (with pics) on this can be found on the hand tool forum.

Re: Drawer slips

#9

Answers

Bill Tindall

Am I correct that the slip is an extension of the drawer sides and actually rides on the cabinet frame?......yes effectively it thickens the drawer side at the drawer side bottom.

If it is, how is it attached to the drawer side....glued as described above. and when is the groove cut for the drawer bottom?The groove for the drawer front is cut before drawer assembly. A piece of wood that two slips can be cut from is shown in the center of Picture 1. As you can see it has two grooves cut in it.

While unusual in American furniture the slip is ubiquitous in English furniture. English drawer sides in the best furniture were made of quartered white oak. Drawer dividers were mahogany. When a slip failed the hard oak drawer side ground a substantial groove in the drawer divider over time, as can be seen in some English antiques. So clearly the slip was a means of lessening the wear of the narrow hard side on the softer divider.

Generally it is easier to repair a worn drawer than a grooved divider. Hence, it is better to make drawer sides from a wood that is softer than the drawer divider for long term durability in a situation where the drawer will be used a lot or heavily loaded.

Re: Drawer slips

#10

Drawer divisions vs blade rails

Andrew F in Australia

Hi Bill,

One minor point, and it's fairly trade specific.

When I was reading your post, I was wondering how a division would get worn by the slip, then it twigged.

The divider/division is the vertical timber piece in the front of the carcase that separates the sides of two drawers, while the blade rail (drawer blade) is the horizontal rail at the front of the carcase that supports the load.

Cheers,

AF