Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

6" jointers

Posts

6" jointers

#1

6"  jointers

Paul Blackwell

I recently downsized from our place in the country with four acres and a 24 x 40 shop to a new house on 1/3 acre with no shop. I sold off some of the larger equipment, and yesterday with the help of a couple of buddies with pickup trucks, we moved the rest and carried it piece by heavy piece down the cellar stairs and believe me, we felt every one of the twelve stairs up and down. I am now looking for a new 6" jointer, and have perused several sites. Grizzly has the 6" Polar Bear series with mobile base on sale for $410, and the 6" parallelogram table with spiral indexable head for $799. Delta's is $699 with standard head as is Jet's for $799. Anybody have any experience with any of these models? Weight to move it down the stairs is a concern. Is the indexable spiral head worth the extra money? Any and all comments appreciated.

Re: 6" jointers

#2

Re: 6"  jointers

del schisler

What is wrong with this one http://www.ridgid.com/Tools/JP0610-Jointer/ It has a life time warrenty. I have one and use it every day. It was right on right out of the box. Just had to set the fence for the correct degree's. It has a out feed movable bed which is good when you have to change the knive's. I have had mine for a couple yrs and the knives are still fine. Cut's very good with a dust shout a 4". I look and it is priced online at $429 it may be lower at other stores?? my 2 cents

Re: 6" jointers

#3

JL

Re: 6"  jointers

JL

My usual response is to get the longest, heaviest jointer. That really won't work well in your case. Have you considered a combination jointer/planer? There are a couple of reasonable 10" and 12" units out there. They have the advantage of being "short" and they would allow you a bit more leeway in terms of positioning tools.

I like the Rikon 6" jointers. I also think their jointer/planers are good tools. Do you have 220 V? If so, you could consider the Rikon 12" Jointer/Planer. I checked them out (both the combos and the jointers) a while back.

There aren't too many "lemons" out there in terms of 6" jointers. The market is quite competitive.

I think your determining factor will be what you can get down your stairs. I have a "daylight" basement, so mine was what I could get around the house. Good luck.

Re: 6" jointers

#4

Re: 6"  jointers

Larry Clinton At Frankfort, (Central) Indiana

I certainly am not a pro so my information is worth what you pay for it. I used a 6" Grizzly joiner for 10 - 15 years and was pretty satisfied with it - then I replaced it with the Griz 8" with spiral head. I really saw a great difference in certain woods like Locust, and any with wild grain. There is almost never any tear-out and the surface has less tool marks. I have been using it for about 6 years and am just about ready to rotate the carbide inserts for the first time. Based on my experience with my 20" Byrd head on my planer, this will take me about 1/2 hour. The last time I changed the blades on the 6" I spent the better part of a day before I was satisfied with the alignment. The new carbide lasts at least 10 times longer (per each of the 4 sides) so about 40 time before I have to purchase new inserts. I would never go back to a straight blade unit. By the way the Grizzly joiner does give just about the same results as the Byrd head in my planer as far as I can tell - very happy with both.

Re: 6" jointers

#5

Re: 6"  jointers

paul in AZ

I have a Ridgid which has been reliable and trouble free for years now. got it on one of their periodic sales.

The only trouble it ever gave me was my fault. Lifting the bed out of the box I sprung my back. Only later did I pay attention to the assembly directions that warned that the bed is heavy and I should get help. Duh! It is heavy.

Re: 6" jointers

#6

Re: 6"  jointers

Tony - memphis

While I had some issues initialy with my Griz 6", it has been a good solid piece of equipment for around 14 years. They used to have a store here and their customer service was awful. My jointer had a fence pivot issue and their attempts at fixing it included sending me several parts that were as bad or worse than the original. I fixed it myself and it has been fine since. I've sworn I won't do business with them again, but when I look at 8" jointers, it is tempting. I would like to move up to an 8" with a spiral head. I've read enough that I am pretty sure I wan to go spiral next time. And six inches never seems to be wide enough for the stock I buy. The extra bed length would be nice too. I just need to find the space, money, and power...but that's all!

Tony

Re: 6" jointers

#7

Re: 6"  jointers

Jason Waters

I don't have any of those. I have a Jet Shopline 6" I bought over 10 years ago when Lowe's clearance them for like $225-250.....

I would love to have a longer bed too, but for jointing 8' and less I have never needed any more, using proper technique, and after aligning my jointer. I'd much rather have 8" wide than a longer bed. The 12" planer/jointer combo looks interesting, but combo machines haven't been to my liking, but I have never looked at a planer/jointer combo.

So I think a 6" is fine, if you can live with the limitations. Check out the fence and make sure it's easy to adjust and sturdy. I only joint at 90 degree 99% of the time so mine works fine for me.

That being said, the carbide insert cutterheads do intrigue me, and I can imagine they work well, particularly for troublesome wood.

Jointers are fairly well developed pieces of equipment, so most should be adequate with tuning. I think I probably used an article from FWW or Shopnotes to tune mine and it made all the difference.

Might I suggest you look in Craigslist and on Ebay (with a search radius), you might be surprised what you find. I generally pay 1/2 used for the same tool new, if it's in like new or very good condition. And you might get a mobile base or some other stuff. It's worth considering.

If you aren't handy with fixing stuff, then don't get a beater for $50......

Good Luck on the quest, and let us know what decision you arrive at.