Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This $39 jig will make you a WOODWORKING GOD!

Workshop Lighting

Posts

Workshop Lighting

#1

Workshop Lighting

Steve Kirincich

I moved into my current house almost seven years ago, and quickly learned that the basement area that would become my workshop needed a serious lighting upgrade. I have installed a number of eight foot fluorescent fixtures that have worked well right up to the point when the cheap ballasts die. I haven been able replace some ballasts over the last few years. I have considered switching to compact fluorescent lights (CFL) employing an array of smaller but more numerous fixtures. I think the eight foot fluorescent bulbs are not convenient to store and dispose of, and they may eventually be discontinued from production. I am reading some the relevent lighting articles from FWW, but any comments and suggestions would be appreciated.

Steve

Re: Workshop Lighting

#2

Re: Workshop Lighting

Larry Clinton At Frankfort, (Central) Indiana

I agree, the 4 foot dual light fixtures are so cheap that I consider them disposable. When I built my shop about 5 years ago, I installed around 20 of the "shop light" type fixtures and 5 or 6 standard incandescent light with 100 Watt halogen bulbs. The other real advantage to me is the variety of bulbs available for the 4 foot units. I have pretty well settled on the Higher temperature "sunlight" bulbs - they make it a lot easier for me to see tool marks, cut lines etc. than the cool white style. These fixtures were in the $10 to $15 range, many included bulbs (most of which I later replaced with the above bulbs). I installed my lighting by wiring 4 separate circuits, one control the halogen ceiling lights, and one for each strip of ceiling outlets that the 4 ft fixtures are plugged into. They are hung by very short chains so changing the fixture would only take a few minutes. Actually I don't believe I have had any go bad - did have one that didn't work when installed - store replaced it without issue.

Re: Workshop Lighting

#3

Re: Workshop Lighting

Bill Tindall

Check out my Article in the Articles Section. My brother in law is a lighting engineer. I used to not like working in my dungeon basement but after installing his lighting design I can see and it is less stressful working.

You have to work hard to get as good as daylight.

Re: Workshop Lighting

#4

JL

Re: Workshop Lighting

JL

I have several 4' fixtures in my shop. These are for general lighting. I have sets of track lights in my primary work areas.

I use compact fluorescent PAR 30 lights in my track lights. I prefer those because they are somewhat directional and get the light where I need it.

Re: Workshop Lighting

#5

Steve Strickland

Re: Workshop Lighting

Steve Strickland

You might also look into LED lighting now that bulbs are under $15.

Re: Workshop Lighting

#6

Re: Workshop Lighting

George Colonel's Workshop-Havertown PA

Good Afternoon Steve,

I got rid of the original 8 foot fixtures 15 years ago, and installed the 4 foot variety flourescent bulbs. These are for general lighting, and are totally satisfactory, as well as being relatively inexpensive. I use a couple drafting table lights on work tables when needed. Otherwise, a have soffet mounted hi-hats above my drill press, table saw, router table and SCMS. I find that the new squiggly flourescent replacement for the 60 watt incandescent works quite well in the hi-hat fixtures.

George

Re: Workshop Lighting

#7

4" light fixtures, but don't be too cheap

Hoa in Alameda

My shop is a garage with 3 stalls. When I moved it 17 years and 2 days ago, I installed a bunch of fluorescent "shop lights," the cheapo version, about $15 - $20 a copy.

Over the years, I found that the bulbs and the ballasts needed to be replaced so often it became annoying. Also, the lamps flickered too much and didn't work reliably when they were cold. Three years ago I replaced them with track lights (left over from a remodeling project) and CFL bulbs. The CFL bulbs turned out to be a poor choice: they didn't work well when cold, and the light fixtures were dust magnets.

Earlier this year, based on my good experience with T8 fluorescent lights with electronic ballasts somewhere else in the house (the bulbs lasted 10 years with 8 hrs/day), I replaced the track lights with 4' T8 fluorescent light fixtures. They are reasonably priced ($30 fixture + $8 for 2 bulbs), reliable, bright and they flicker much much less.

Re: Workshop Lighting

#8

Re: 4" light fixtures, but don't be too cheap

nickb

A second for 4', twin bulb strips. I got mine with a reflector (and "guarded" the tubes by putting chicken wire across the reflector for those fixtures that see a lot of boards swinging around - I've bumped the chicken wire a number of times but no broken tubes yet). The fixtures were installed about 6 years ago and no problems so far. Love all the light, although I think I should have put a second fixture over my main bench.

I think I paid $35 or so per fixture. I bought a case of tubes pretty cheap and I was all set.