Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

Power Twist Belt Question

Posts

Power Twist Belt Question

#1

Power Twist Belt Question

Will Williams

I am considering treating my 1973 vintage Rockwell Delta bandsaw to a new drive belt.

After reading the instructions on the Fenner Drives website I was surprised by how involved the measurement / installations were.

I was wondering if any of you guys who have used these on their machines went by the instructions.

Maybe it is much less "intense" :-) when you actually have the belts in your hands, who knows!

The video makes it look pretty straight forward too.

Here is what they say:

I. How to Measure

Pull belt tight around pulleys to check hand tight length, overlapping

the last two tabs with two holes in matching links as shown. Count the

number of links and remove one link for every 24 of 3L, Z/10, A/4L and

B/5L sections, and one link for every 20 of C and D sections. This gives

the correct installed belt length and will ensure optimum belt tension

when running.

Note: Every tenth link is designated with an arrow (➞) (3L, Z/10, A/4L and B/5L only).

For multiple belt drives, ensure that each belt has the same number of links.

IMPORTANT — Turn belt INSIDE OUT (as shown) to ensure easy assembly

and disassembly.

II. Disassembly

A. Hold belt upside down. Bend back as far as possible; hold with one hand.

Twist one tab 90° parallel with slot.

B. Pull end of link over tab.

C. Rotate belt end with tab 90°.

D. Pull belt end through two links.

III. Assembly

A. Hold belt with tabs pointing outward.

B. Place end tab through two links at once.

C. Flex belt further and insert second tab through end link by twisting tab with thumb.

D. Ensure tab returns to position across belt. Reverse belt so tabs run inside.

IV. Installation

1. Turn belt with tabs to the inside before installing.

2. Determine direction of drive rotation.

3. Belt must travel with tabs trailing or following the

belt direction arrow (➞).

4. Fit belt in nearest groove of smaller pulley.

5. Roll belt onto larger pulley, turning the drive slowly. Belt may seem very tight; this is ok;

DO NOT JOG MOTOR.

6. Check to see all tabs are still in their correct position and are not twisted out of alignment.

7. For multiple belt drives, work belt from groove to groove. On particularly wide drives, it may

be easier to install half the belts from the inboard side and half from the outboard.

Note: With drive ratios around 1:1, it may be necessary to add back one link to allow belts to be

rolled on. This does not apply if using the Alternative Installation Method.

V. Alternative Installation Method

1. Set motor to mid-position of adjustment range and mark base clearly.

2. Determine required belt length as in I.

3. Push motor forward to minimum centre distance.

4. Install belts as in IV.

5. Pull motor back to previously marked mid-position.

VI. Retensioning

Like all high performance V-belts, PowerTwist Plus V-Belts require the maintenance of correct

drive tension to operate efficiently. Experience indicates that drive tension should be checked

after 24 hours running at full load. A retension may be necessary depending on the severity of

the drive. Any initial belt stretch is then taken up. Subsequently, belt tension should be checked

periodically and adjusted

when necessary.

HOW TO MEASURE, ASSEMBLE & INSTALL

A B C D

A B C D

View the PowerTwist Plus Installation video at:

www.youtube.com/FennerDrives

Belt Direction

Re: Power Twist Belt Question

#2

Re: Power Twist Belt Question

Bill Howatt

Glad I never read the instructions other than how to remove links.

I just made a rough measurement, removed the excess links, put on the belt and used the regular adjustment mechanism to get the tension set. If the length isn't correct, it's easy to add/remove links.

Bill

Re: Power Twist Belt Question

#3

Re: Power Twist Belt Question

Bruce, a MN Galoot

Glad I didn't read the instructions, either. I just put one belt on top of the other and adjusted links. It's a good think I didn't know how complicated it was to assemble the belt -- it would never have gotten done :D

It's a snap. Just look at it. You'll figure it out.

I put mine on the tablesaw and it all but eliminated vibration.

Re: Power Twist Belt Question

#4

Re: Power Twist Belt Question

Brian in SLO

Sounds like those instructions were written by a gov't employee.

When putting them on my Unisaw I just made sure all 3 belts were equal lengths, put them on the pulleys and adjusted the motor for tension like any other belt(s). Runs like a champ!

Re: Power Twist Belt Question

#5

Re: Power Twist Belt Question

Lee Schierer McKean, PA

Make sure you follow Step IV-4 as the belts will howl if they run the wrong way. DAMHIKT.

Lee