Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

How do you all soften edges?

Posts

How do you all soften edges?

#1

How do you all soften edges?

Bill Tindall

There are a lot of edges on 7 drawers and I like to soften them all. I don't like touching a sharp edge in furniture. I've tried block plane, spoke shave, sand paper. Yet another one of those things I have not settled and await sage advice.

Re: How do you all soften edges?

#2

Why, LV of course !

steve mackay

I used to sand but LOML got me this little thingie from LV. I LOVE it ! Crisp, clean, even edges.

Mini Edge-Rounding Plane

07P15.07

Re: How do you all soften edges?

#3

Ellis Walentine

Re: How do you all soften edges?

Ellis Walentine

Finish sanding the surfaces before you start the softening process. That way, whatever you do to the edges won't be lost when you finish-sand the adjacent surfaces.

Edge treatments have both shape -- e.g., round-over vs chamfer vs something else -- and size, as in the size of the radius or chamfer. If there is a need for a certain feel, then that will impact your choice of shape and size.

Uniformity is key. If all you want to do is just kill the edge slightly so it doesn't cut you, I suggest wrapping a piece of fine sandpaper around a piece of leather to create a flexible edge-sanding block. Fold this over the edge and sand carefully, keeping an eye on your progress so you don't soften too much in any particular area.

Ellis

Re: How do you all soften edges?

#4

Re: Why, LV of course !

Bill Tindall

Checked it out. If you say it works it will get ordered.

Re: How do you all soften edges?

#5

Clint Searl

Re: How do you all soften edges?

Clint Searl

Depends: 220 drywall sanding screen to soften the edge; tapered steel alignment punch to compress the edge; block plane to champfer the edge.

Clint

Re: How do you all soften edges?

#6

Radi-plane

Pat Evans

My LA Mathers Radi-plane is probably the same thing as the LV. The Mathers had two adjustable blades in a wooden body. As long as you go with the grain, it is great. When the grain is a little wild, it can be tricky. None the less, it gives a very uniform small radius edge.

Re: How do you all soften edges?

#7

Re: How do you all soften edges?

FredD

" tapered steel alignment punch to compress the" Drift Pin by any other name...

FredD

Re: How do you all soften edges?

#8

Re: How do you all soften edges?

FredD

Expanding a littel on Ellis , it has been my understanding for years that the East Coast preferred crisp edges and the West softer ones. That may be pure BS ,but it has been stated over the years in amny Wood Mags.

For myself , I don't like crisp edges because they damage more easily then rounded ones and leave very little surface for film finish.

Many times I start out with a carbide 1/8th inch rounding over bit and then clean it up with finish sanding. Less sanding that way and very uniform in appearance.

FredD

Re: How do you all soften edges?

#9

Depends on the look...

John in NM

If I want a mini-chamfer it's with a block plane or file followed by a touch of sandpaper if needed.

Alternatively I also use a 1/16" round over bit in a laminate trimmer and a file to get in the corners. Shop I used to work for always used 1/8", but I found it a bit too big for my own taste.

Re: How do you all soften edges?

#10

Steve Strickland

Re: tiny edge bevel

Steve Strickland

Set up a sacrificial fence on the table saw. Raise blade about 1/4" and tilt to 45 so it cuts into the fence. Just slide each edge down the fence. Adjust size with test pieces. It's very fast and looks good.

Here's a sample:


img

Re: How do you all soften edges?

#11

Moses Yoder

Re: How do you all soften edges?

Moses Yoder

A block plane leaves teh smoothest eased edge, barely visible to the naked eye but you can feel it, set fine and make 3 or 4 passes. If you had 12 boxes to do it seems like it would take a while but I bet if you just did it you would be done in 30 minutes or an hour.

Re: How do you all soften edges?

#12

I use my ROS

Keith Newton----Little Rock, Arkansas

while I am sanding the edge, then just tilt 45º and knock the corners with a quick pass. When doing the insides, care must be taken to not let the paper hit in the corner. If you bang into the other side, it will not only wrinkle / tear the sanding disk, it can damage the edges of the pad.

A little abrasive scratch can improve getting the finish to stay there, rather than shrinking away as it does on sharp slick corners.

Re: How do you all soften edges?

#13

Re: How do you all soften edges?

Paul Leuba

I also use a 1/8" roundover bit on a router followed by light sanding. It's uniform and leaves just the right amount of edge relief for me.

Paul in Hunt Valley, MD

Re: How do you all soften edges?

#14

Used Sanding Discs

Thomas Skaggs, Foothills of Mount Level

I soften the dges on most of my work. The easiest and fastest way I have found is simply by hand with sandpaper. What I use are used 5" sanding discs from my ROS. I simply fold them over into a half moon and push them into my palm. I just take them along edges at a 45 degree angle in a circular motion. Fast and simple.

Tom

Re: How do you all soften edges?

#15

Re: How do you all soften edges?

David Weaver

Any plane that I have close by that is not too large so as to be ungainly doing the job. If I only had a spokeshave out, I would use that, but that hasn't happened yet.

Re: How do you all soften edges?

#16

Re: How do you all soften edges?

Jim Dillon

Bill,

I keep a 1/8-inch RO bit permanently installed on my laminate trimmer for rounding over edges. If I want to just break the edge, I use sandpaper and a cork sanding block and just take a few uniform swipes. Works for me. I do have a 1/16-inch RO bit, but can't say I have ever used it.

Jim