Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

Lift A Unisaw by myself?

Posts

Lift A Unisaw by myself?

#1

Steve Strickland

Lift A Unisaw by myself?

Steve Strickland

I have a poser...

How can I lift a Unisaw off a mobile base and put it on the original base working by myself?

I thought I might pry bar and block the machine up enough to get a couple of beams under it, then pry + block the beams up enough to roll the mobile base out. Put the original base under it and pry bar it all back down.

I suppose I could bolt a couple of beams to the lower cabinet and lift it with block and tackle. This might be easier and safer.

Then I'll have to get a right wing and replace the fence.

The mobile base is nice but it's huge. Useless for puzzle making, it's just wasting a lot of valuable floor space. My biggest cut is about 4 inches and this thing is almost 8 feet long.

Re: Lift A Unisaw by myself?

#2

how I lifted a 1100 lathe, and failed a 600 #plane

Bill Tindall

first the planer. Tried to get it pried up and onto a base. Tipped over and broke wife's leg.

For the lathe I ran 2 - 3/4" bolts through a joist above the machine's location. Fastened come-a-long to each and the lathe, and with ease lifted it up 3' to slide a base beneath it.

Re: Lift A Unisaw by myself?

#3

Alan Young

I could have told you

Alan Young

A wife's leg is too fragile for prying purposes!

Re: Lift A Unisaw by myself?

#4

Steve Strickland

Re: new he's gotta...

Steve Strickland

chop the wood, haul the water and slop the hogs himself until she heals.

Re: Lift A Unisaw by myself?

#5

Re: Lift A Unisaw by myself?

Thomas Skaggs, Foothills of Mount Level

How about renting an engine hoist?

Re: Lift A Unisaw by myself?

#6

Only with a hoist...

John in NM

My unisaw is from the early 1950's, and weighs roughly 300+ lbs. I've lifted it with another person onto a mobile base, but would not try it alone, they are top heavy. I have hoisted from a truss roof, though there are risks of compromising the trusses doing this. Last time I used a spreader to distribute the load to two trusses and hoisted near where the ties between upper and lower chords connect.

As Bill notes, moving equipment can be dangerous, and caution is the rule - I'd rather spring a roof truss than injure myself or a helper. So I'd say either get a friend with a strong back or hoist the machine. Tipping is very dangerous.

For what its worth, I use a heavy webbing strap (made for towing a vehicle I think) to hoist my saw. Just loop under the table each side and cross in the middle. No need for boards, the table is quite securely bolted down and the stress on it is minimal. Jointers and planers can need re-aligning after hoisting from the working surface though.

Re: Lift A Unisaw by myself?

#7

Re: Lift A Unisaw by myself?

john lucas

I moved a 450 lb Smithy lathe mill combo machine by myself. I rocked it to oneside and kicked a 2x4 under it. then rocked it to the other side and did the same. I had to put 6 2x4's under it to get it up close to the table height. I was putting it on a rolling table but the table was higher than the truck. I jacked the truck up with a hydralic jack to get to the table height and then rolled it onto the table by lifting each end of the 2x4 and sliding thick wall conduit under the 2x4's. Getting the 2x4's out from under was more difficult because the rolling table wanted to roll but I finally managed.

They put the Smithy in my truck with an engine hoist. I'm saving for one of those because moving that or any other big machinery is difficult and dangerous by yourself. I think I might be able to find a storage area for one of the folding engine hoist.

Re: Lift A Unisaw by myself?

#8

And lift from the top!

Stephen

Having done this a number of times, I would like to echo the comments above.

1. Use the web lifting straps. They are made for this purpose, distribute the load along the strap, and do not scratch the tool.

2. LIFT FROM THE TOP!: Almost all the tools we use are REALLY top heavy. Strap around the table. I flipped a Woodmaster 26" Sander lifting from the bottom after it was only an inch off the ground.

Re: Lift A Unisaw by myself?

#9

Worse than you think......

Bill Tindall

It happened in 1971. I drove her to emergency room in our 1965 bug. While in town (lower elevation by several hundred feet) it began an intense wet show. By the time we got back to the road we lived on the snow was many inches deep because it had started to snow much earlier at the higher elevation. The VW had excellent snow traction.......so long as the wheels were on the ground. But the snow on our road exceeded the ground clearance and soon the bug was lifted into the air by the snow packed under it. Had to carry wife, and cast, through the snow to home. I remained on best behavior for quite some time after.

Re: Lift A Unisaw by myself?

#10

Re: Lift A Unisaw by myself?

Carol Reed, Strawberry, AZ

Wimpy me has three hoists; an electric one that I use to lift sheet material, a shop crane for tools and heavier stuff, and a truck bed crane fastened to the porch. It lifts stuff from the ground unto the porch. All are from HF and each cost less than visits to the chiropractor for doing something stupid. Also have webs galore.

All much cheaper than getting hurt!

Re: Lift A Unisaw by myself?

#11

Re: Lift A Unisaw by myself?

john lucas

You take all the fun out of it. I just holler, hey bubba watch this before I start lifting anything bigger than I am. that pretty well covers me no matter what. :)

Re: Lift A Unisaw by myself?

#12

Look! Up in the sky! It's a bird, it's a plane, no


Re: Lift A Unisaw by myself?

#13

Re: Lift A Unisaw by myself?

Mark Mandell - Gone Round In Jersey

Steve,

Years ago I bought shares in a medical products company here in New Jersey. I've since become friendly with one of its VP's.

I can get you a good deal on a hernia repair mesh, but the cost of the doctor etc. is on you.

That said, since you're redoing to top anyway, take it (and the fence) off in pieces then unbolt the motor. The stripped cabinet and trunions are fairly easy for a 1-man move.

Re: Lift A Unisaw by myself?

#14

Dale Lenz

Back in the day...

Dale Lenz

When I was fourty something, moved my Walker-Turner cabinet(several hundred #'s) saw a few times by myself. Back the pick up next to shop door, have heavy blanket in bed of PU. Tilt saw to where table saw's table is leaning on downed tail gate of PU. Pick up bottom of saw and flip saw over on it's top, in a smooth somewhat slow motion. My saw, 1950 circa, still has the factory castors, and don't move too well, so your mileage could vary. If you have a Bes fence, take off before trying this. Obviously, two people would be safer.

Good luck

Re: Lift A Unisaw by myself?

#15

Re: Lift A Unisaw by myself?

Larry Clinton At Frankfort, (Central) Indiana

Rent, borrow or buy a folding engine hoist, makes it (along with many other heavy jobs) a breeze. I decided to purchase one when my Ford 9N tractor required "splitting" to replace a flywheel gear. I was lucky to find one at Rural King that was in a torn up box. They sold it to me for $150. Only issue I have is finding storage space for it. If you have any friends that do a lot of Automotive work I'm sure they would loan one to you. If you were close to me I sure would loan you mine.

Re: Lift A Unisaw by myself?

#17

Kneale Brownson

Jack it up

Kneale Brownson

A 2X board under each wing next to the cabinet, two hydraulic jacks and something sturdy under each to let you raise the saw high enough to make the change in bases.

Re: Lift A Unisaw by myself?

#18

Re: Splitable base?

TdomD

To just get a splitable base under there you just rock the machine, or pry it, up an inch or two, then split the base and slide it off. It should not be necessary to lift the saw. An easy one person job. If it has to be lifted completely free of the base, drag it over to some solid stuff like a bench, or machines, and rock and jack it up so it rest above the ground on the solid objects, supported by the table. If it has an open based, slide a big board in there, and hook one end over a chair etc... Lever the long end of the board, and get some one to stuff a chair under there. If you really don't have anyone, rig is so a falling weight will tug the chair under when you lift your end up.

In general, if you are working with heavy iron, some kind of crane, like an engine crane is worth it's weight in gold to an old galoot. Just the other day I was using mine to pull out saplings, lots of uses. My best deal ever is this thing I got from a machinist that looks like dolly, but also has a winch in it. I posted a pic of it last year in a thread on beech I harvested