Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

OT Removing Writing from mugs

Posts

OT Removing Writing from mugs

#1

OT Removing Writing from mugs

Barry Irby

I mentioned a friend of mine buys truck wreck merchandise and resells it. It is astounding what he finds and sells and how much of it there is. He ended up with hundreds of mislabeled mugs. They have misspelled words on them and other defects. Is there any practical way to remove the writing? If they were blank he could sell them for more. Anybody need some mugs?

Re: OT Removing Writing from mugs

#2

Moses Yoder

Re: OT Removing Writing from mugs

Moses Yoder

My father in law gave me a tee shirt once from Master Bait & Tackle company. If he had one of those mugs, even with misspelled words on it, I would probably give him $10 for it.

I am not sure how the lettering is applied but I think most mugs have a protective coating over the lettering, so the mug would be ruined if the lettering was removed. Some things are just destined to be used as fill.

Re: OT Removing Writing from mugs

#3

Re: OT Removing Writing from mugs

Ken Oakley-Sunny St. Cloud, Fla

If it is a ceramic mug the lettering is fired on and then glazed over and fired again. Impossible to remove. If it is a fired on decal which is more likely, it can possibly be burned off by refiring in a kiln at 1800 degrees or more. My wife and I have been involved in ceramic for over 50 years and we have done the above with mixed results.

Re: OT Removing Writing from mugs

#4

already have way too many


Re: OT Removing Writing from mugs

#5

Steve Strickland

Re: OT Removing Writing from mugs

Steve Strickland

I used to work for an outfit that made those.

Some are printed with silkscreen. This type ink can be cleaned with acetone or some other keytone copolymer solvent. You'll have to soak 'em a good long while.

Many are done with a transfer and there are 2 main types of adhesives. Both can be removed with acetone. Most transfers are polymer plastic that will dissolve in acetone. Some use a metallic transfer where the adhesive can be softened in acetone then the transfer peeled off.

Using acetone is dangerous. The vapors cause brain and liver damage and are about as explosive as gasoline. It damages eye and nose tissues. Take all safety precautions when using it. Don't breathe the fumes at all and make sure there are no sources of sparks such as light switches. Constantly ventilate. Wear chemist gloves and goggles. Attach a ground wire to your wrist to eliminate static sparks. Check OSHA for full safety guidelines.

Re: OT Removing Writing from mugs

#6

Toxicity of Acetone

Howard Acheson

While acetone must be treated with respect, it is one of the less dangerous chemicals to humans. In fact, the human body produces it naturally and its production is increased in pregnant women. It is explosive but not particularly toxic to humans.

Google "acetone" and see the health section of the Wiki write-up.

Re: OT Removing Writing from mugs

#7

Ric Taylor

Not According to My Doctors

Ric Taylor

My doctors are in agreement that acetone is very dangerous and does cause liver damage, even in amounts that are absorbed through skin. Once your liver is gone, you are history.

Always wear gloves when working working with acetone, and avoid breathing fumes as much as possible.

Ric

Re: OT Removing Writing from mugs

#8

Re: Not According to Wikipedia and its sources


Re: OT Removing Writing from mugs

#9

Setting the record straight on acetone

Bill Tindall

I often wonder where the paranoia over commonly used chemicals comes from. It would seem in this case misleading or misinterpreted information from a trusted source, namely "the doctor". Unless the doctor has specialized beyond the limited chemistry they may have been required to endure as an undergraduate, they are no more qualified to interpret toxicology data than anyone else with some exposure to chemistry, and this presumes they have at least read and understood the MSDS for a chemical in question.

So, step one in dealing with any chemical is to read the material provided on the container. Step two, obtain, either from the manufacturer or off the internet, the MSDS and study it. These sources of information are the most reliable to be had. In the case of acetone, it is so commonly used that there is also a great body of information that results from experience using it in manufacturing.

After studying the available data then decide what your short and long term exposure is likely to be and take appropriate precautions guided by the information in these sources. Keep in mind that the short term exposure amateur woodworkers are likely to encounter is vastly less a threat with most chemicals, than a worker exposed for an 8 or 12 hr shift.

Indeed, the conclusion from all the sources is that among the solvents acetone poses a toxicology risk not much different than ethanol and less than many other commonly used woodworking solvents. Exposure at a concentration where there could be short term toxicity would be a situation where flammability would be an alarming concern.

That said, it is never a flawed practice to minimize exposure to solvents both for toxicity, and more relevant, flammability concerns. The often encountered statement of "use with adequate ventilation" is well founded. A good rule of thumb is to treat all woodworking solvents as you would treat gasoline. Most are not quite as flammable nor quite as toxic as gasoline.

The issue of gloves and solvents is not a simple one to decide. Some gloves are permeable to solvents. Other gloves are clumsy and could lead to spills. An undiscovered leak/tear in a glove can lead to concentrated exposure and irritation (been there and done that). Personally, I don't use gloves with solvents. None of the solvents I use present any significant risk of harmful exposure by short term contact to the skin. They all evaporate so quickly that any accidental skin contact is very short term.

The exception is stripper containing methylene chloride. I use it with heavy impermeable gloves because contact over extended time will result in severe irritation.

As an aside, when one of my sheep's breath smells of acetone they are on death's door, not from the acetone, but from the fact that their metabolism has gone amok and their cells are making acetone and not CO2. Treated promptly with either glycerin or 1,2-propane diol ( one variety of antifreeze) they can recover in minutes. The alternative it too gruesome to describe on this Forum. The chemistry of the cure is interesting. Six ounces of these chemicals into the rumen provides the cells with a prompt energy source equivalent to an IV of glucose.