Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

1975 Craftsman jointer

Posts

1975 Craftsman jointer

#1

1975 Craftsman jointer

Carol Reed

I 'inherited' this gem from a local widow. Heavy cast iron monster. Only 6" but more than adequate for my purposes. I liberated the knives yesterday. Took some doing, too! They weren't fit for spreading butter but a local sharpener took care of that. No time to send them to Scott. Next time.

General clean-up and straightened out some wiring issues. One day it will go on its own wheeled cart with a decent motor and shavings collection system. A little rust removal on the infeed table needed, but not bad. All in all, a fairly good tool that served without any real maintenance, worthy of a second chance. Even got the book. And the price was more than right! Good to be known as a local woodworker, in addition to pastor. The members keep me blessed.

I Googled for a replacement pork chop guard as that is missing. No longer available. Anybody ever make something like this - or have one laying around?

Also, Sears wants $38 for replacement knives. Reasonable? Other places to look?

Re: 1975 Craftsman jointer

#2

Joe Bradshaw

Re: 1975 Craftsman jointer

Joe Bradshaw

Carol, shoot me a pm with your address. I think that I have one or two sets of knives for this jointer and also maybe a guard.

Joe

Re: 1975 Craftsman jointer

#3

Re: 1975 Craftsman jointer

Carol Reed

carol.j.reed@gmail.com

model # is 113.20680.

Thanks, Joe.

Re: 1975 Craftsman jointer

#4

Jim DeLaney, Austintown, Ohio

Re: 1975 Craftsman jointer

Jim DeLaney, Austintown, Ohio

Carol, I made a pork chop for my old Delta. I used plain ole 4/4 poplar for mine, and used a piece of (I think) half inch steel rod, with a lengthwise slot cut in the bottom to accept the tensioning spring, and pinned in place to the pork chop. It only took about half an hour to make. Also, I glued a small knob to the top of it so it's easier to retract without any chance of fingers meeting knives (even when the jointer is off!).

Re: 1975 Craftsman jointer

#5

Re: 1975 Craftsman jointer

Carol Reed

That's good info, especially about the slot to grab the spring. I wondered about that. Thanks, Jim.

Re: 1975 Craftsman jointer

#6

Re: 1975 Craftsman jointer

del schisler

I used to have that jointer. The knives are a job changing and get set right Good luck with it

Re: 1975 Craftsman jointer

#7

Re: 1975 Craftsman jointer

Dick Coers

Is that the machine with a fixed outfeed table? They are a bit@# to get set right. You may look into some type of magnetic setting aid because getting them parallel and just a few thou above that table is really tough. I was really glad to to get rid of mine. Probably did that sometime around 1976! LOL.

Re: 1975 Craftsman jointer

#8

Re: 1975 Craftsman jointer

Carol Reed

Funny. I had no problem. I do have the magnetic thingy but forgot how to use it. Went back to the old steel ruler and trial and error. Took a little less than an hour, but then I haven't done this in a while. Th trial cut looked good, but I think that has to do with the excess speed. See other thread.

Re: 1975 Craftsman jointer

#9

Re: 1975 Craftsman jointer

Doug Turner

I made a blade guard from a piece of 3/4" plywood and a bolt for the shaft. A thread nut allowed attaching the plywood to the bolt and a hacksaw cut in the bottom of the bolt for the spring did the trick. You can adjust the tension by loosing the nut and turning the plywood and then retighting.