Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

aquarium stand plans

Posts

aquarium stand plans

#1

aquarium stand plans

pharmd99

I'm trying to build a plan for an aquarium stand. My aquarium will be 60"wide x 24"deep x 30"tall and when filled will weigh about 2400lbs. I want the stand to be 36" to 40" tall and I need to maximize the amount of space INSIDE the stand for all my equipment.

The stand will be 61"wide x 25"deep x 36"tall. I'm concerned about the stand being top-heavy and i'm not sure if these stands can handle the dimensional stress's.

I have attached a couple of cad plans, please let me know if you can help me.

thanks,

dave

PS - stand 4x6 is made with 4x6, 2x6 and 2x4's

- stand1 is made with 2x6 and 2x4's

- stand4x4 is made with 4x4, 2x6 and 2x4's

On top of all the stands will be 3/4" plywood before the aquarium.


img

Re: aquarium stand plans

#2

Clint Searl

Re: aquarium stand plans

Clint Searl

I would be inclined to skip wood and have a steel fabricator weld it. 4" pipe for the legs and 2" angle for the top. It really wouldn't need it for strength, but I'd add some kind of stretcher arrangement out of 3/4" bar stock, which would also support a shelf.

Clint

Re: aquarium stand plans

#3

Re: aquarium stand plans

Grant Wilkinson

I've built several, and (touch wood), haven't had one collapse yet. I use 4" x 4" for the uprights and 2" x 4" for the horizontal members and the braces. I don't do horizontal bracing along the floor, as it can get in the way of moving filters, pumps, etc. I do X bracing at each end and across the back of the stand. I dado the braces into the pots and where they meet in the middle. For tanks larger than 4 feet across, I put one cross brace from the front horizontal member to the rear on. I use cork on the top of all the top members so that the tank self levels.

None of the panels covering the frame are non-load bearing. I make them removable so that it is easy to access all the equipment.

I'm not putting myself out as an expert, so this is all FWIW.

Re: aquarium stand plans

#4

JL

Re: aquarium stand plans

JL

You are looking at about a ton of water (more or less). Some questions - do you need to access the sides or can you skin the sides with some 3/4" (or 1/2") plywood? Do you need access to the back?

I would make the sides and the back to be more like "trusses". I would have diagonals going from the "middles" of the sides down to the bottom corners. I would also have diagonals in the back between the vertical "studs". Maybe a single diagonal would work for both. Anyway, the diagonals are there to support and transfer weight to the bottom "plate". If you have a 3/4" or 1/2" skin of plywood, the sides and the back will be pretty rigid. I would have a single vertical element in the front.

I figure if it can work for trusses, it ought to work for aquariums.

Re: aquarium stand plans

#5

Re: aquarium stand

Ray Carson - Lawrenceville, NJ

I built one similar to this many years ago for someone. Wood is fine but it will be exposed to the water unfortunately. I like the look of a wood standd myself. Steel will rust so pick your poison.

Most of your load is down force so the only thing I would recommend is anchoring it to the wall if there is one nearby. If not, some sort of clip or upturned angle to keep the tank locked to the base at a minimum.

My 2 cents worth.

Ray

Re: aquarium stand plans

#6

Re: aquarium stand plans

Keith Newton----Little Rock, Arkansas

I think you may be a little high on your estimated weight. Saltwater is ~ 64# per cubic foot, and full to the top is 25 cu. ft. or 1500 pounds. I don't have any experience with aquariums this size, but I'll bet the tank will be less than 900 pounds.

As for the load capacity of your legs, any of the drawings will handle that. It is the joints and fasteners that make it strong. If you don't know that part, why don't you frame your question differently. Any of the drawing you've done, may try to rock on and uneven floor, unless shimmed. All will need some kind of skin or bracing to make them strong for side loads.

Re: aquarium stand plans

#7

here are a couple I made last summer

kellyanderson72


Re: aquarium stand plans

#8

whatcha gonna do with it?

Darrin Hill

freshwater or salt? I had a 200 gallon reef tank not too long ago that i had set up for 10 years.... The stand was in really bad shape, but it was exposed to saltcreep all the time.. and anything metal was rusted solid..

I have a new stand for a 600 gallon, but i bought an engagment ring instead of the tank.. the stand has sat in my office for almost 10 years and i've never used it, but the inside is a metal frame that takes 3 people to lift,... with a cover of oak... the guy who built it built houses and did a whole lot of math to figure out the weight...

if you do salt, you gonna have live rock?

Re: aquarium stand plans

#9

Re: here are a couple I made -Outstanding !!

Ray Carson - Lawrenceville, NJ

Your pictures are the reasons I like a wood fishtank stand. Your fishtank stands are outstanding "kellyanderson72". :)

Ray

Re: aquarium stand plans

#10

Re: here are a couple I made -Outstanding !!

kellyanderson72

Thank you Ray, I appreciate it.