Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

Ot Sort Of Gutters

Posts

Ot Sort Of Gutters

#1

Ot Sort Of Gutters

Dustmaker Mike

I am in the process of getting some gutters for the shop and back of my house. They will be 5 inch wide no seem. So here is my question I have a place I can get them made for cost but I have to transport them. The longest piece is 22' next 1s 16 then a 14 foot piece. If I use a 24 foot extension ladder on top of my explorer which is a little over 12 foot when closed will this be enough support for the long pieces? If not any ideas on how to move the long ones? I have about 6 miles of city roads to carry them on.

Thanks

Re: Ot Sort Of Gutters

#2

Re: Ot Sort Of Gutters

John McGaw

Most seamless gutter machines reside in the backs of trucks. Might it not be easier to have the truck come to you and, if necessary, pay them a bit extra for the trouble of driving the six miles and to save yourself the trouble of transporting an unwieldy and fragile load the same distance?

Re: Ot Sort Of Gutters

#3

Re: Ot Sort Of Gutters

Dave Paine

If you can nest them it will help to reduce the net overhang.

Key consideration is to prevent bending. You could cut 5in wide strips of plywood and attach to the gutter with the kind of wrapping tape which only sticks to itself. If the gutter is held in shape, it will not be likely to bend, especially for short trip on city roads - hopefully without storm type cross winds.

Re: Ot Sort Of Gutters

#4

I am going to the

Dustmaker Mike

distributor to get them, if it was in the back of a truck I would not have asked this question(-; I have a few things to pick up at the same time and they have the machine to make them. So I asked if I could buy straight from them and they said sure.

Re: Ot Sort Of Gutters

#5

Re: Ot Sort Of Gutters

Bill Howatt

If I read your post correctly, you have about a 5' max overhang on each end. If you can put the shorter ones inside the longer ones as suggested it would stiffen the overhang. If you have some old plywood you could rip some pieces to fit between the ladder rungs suitably fastened and let it hang out over the ends of the ladder for the gutter to rest on.

Personally, I don't think you have a problem with a 5' overhang. When I had my seamless eavestrough installed the owner was by himself and was handling pieces over 22' by himself - in other words the stuff is pretty strong once it is formed.

Bill

Re: Ot Sort Of Gutters

#6

Clint Searl

Extend the ladder

Clint Searl

Re: Ot Sort Of Gutters

#7

Re: Ot Sort Of Gutters

George Koch

Mike, my thought would be to wrap them over a full 20' length of 3" or 4" PVC pipe wired to your ladder, or even a couple of 2x4s 16' telescoped out to 22' and screwed together. George

Re: Ot Sort Of Gutters

#8

Know any one with a boat?

Lee Schierer McKean, PA

If you have a friend that has a 18' (or longer) boat, you could lay the gutters over the boat and transport them with minimal overhang. I've transported long board home with my boat. I simply open the windshield on the boat and lay them from stem to stern. No problem with police either having too long a load.

Lee

Re: Ot Sort Of Gutters

#9

Re: Ot Sort Of Gutters

Barry Irby

The problem is going o be the front over hang. By the time you hit 70 mph, the front overhang will be looking straight back. ;)

I would extend the ladder and put a 2x4 inside the long one and have it about four feet to the front and six feet to the rear. Nesting them and taping them together to prevent flutter is a good idea. Drive slowly. Maybe 25/30. The problem is you can't tell you have a problem until you have a problem and then its already over.

Re: Ot Sort Of Gutters

#10

Jason Roehl in Lafayette, IN

A slightly contrarian view...

Jason Roehl in Lafayette, IN

I wouldn't extend the ladder. Then you would just have an offset with which to contend.

I also wouldn't use plywood laying flat--that won't add a whole lot of stiffness.

I would nest the gutter sections, then tape several 2x4s inside--enough to cover the length, preferably only 2. If you use 3, then you would want to use some plywood strips to gusset them together.

As a die-hard DIY'er, gutters are something I wouldn't touch. They're only a couple dollars a foot around here, installed. My house has two 54' runs of gutter, so if I ever have them replaced, I'm only looking at a couple hundred bucks--and someone else has the responsibility to make sure they work properly.

Either way, have fun...

Jason

Re: Ot Sort Of Gutters

#11

Re: A slightly contrarian view...

GolfSteve in Calgary

When I built my garage I found it was cheaper for a guy to come to my place and install seamless gutters that it was for me to buy the pieces and install them myself.