Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

BLO under shellac Question

Posts

BLO under shellac Question

#1

BLO under shellac Question

Joe in a Cleveland suburb

Hello,

I have some very curly maple that I applied some thinned BLO to today.

I applied some, let it sit, applied some more, let it sit, then applied more, then wiped it off. All the pieces are outside cooking in the shade.

How long should I let these pieces dry before starting to apply shellac?

Thanks.

Re: BLO under shellac Question

#2

Dale Lenz

I quit doing that

Dale Lenz

Got by with it several times and sometimes had my shellac and other top coat lift away from the BLO. Got to be to risky, so I quit doing it. Your mileage may vary.

Re: BLO under shellac Question

#3

Stephen Shepherd

Re: BLO under shellac Question

Stephen Shepherd

Joe,

The boiled linseed oil needs to dry at least 24 hours in ideal conditions, high temperature an low humidity. Give it a couple of days just to be safe. As long as you wiped off the excess you should be alright.

And thin the shellac and put on several thin coats rather than one thick coat.

Stephen

Re: BLO under shellac Question

#4

Re: BLO under shellac Question

paul in AZ

I use BLO all the time more often going straight to varnish than shellac.

If you've been putting on thinned BLO and wiping excess off after 15-30 minutes, one day or possibly two should be plenty. It should feel reasonably dry and not greasy.

Re: BLO under shellac Question

#5

Re: BLO under shellac Question

FredD

Next time try just some Amber Shellac and see if that doesn't pop the grain to your satisfaction.

FredD

Re: BLO under shellac Question

#6

other's experience

Bill Tindall

A SAPFM member that does very high end stuff often oils before shellac. He told me to wait several days. I suspect you need to wait until the oil fully reacts with oxygen to "dry". This rate depends on humidity and temperature. Days at 80 degrees could be weeks if colder and damper.

Re: BLO under shellac Question

#7

Re: BLO under shellac Question

Joe in a Cleveland suburb

Thanks all.

From the sounds of it, I should give it a few days.

Thanks again.

Re: BLO under shellac Question

#8

Re: BLO under shellac Question

Howard Acheson

Shellac is a finish that has high resistance to air penetration. BLO cures by mixing with oxygen pulled in from the surface of the wood. Putting shellac on before the BLO has cured will stop or severely slow the curing of the BLO.

Best to give the BLO at least five day--seven days is better.

Re: BLO under shellac Question

#9

Stephen Shepherd

Re: BLO under shellac Question

Stephen Shepherd

The linseed oil will penetrate more deeply into the grain than shellac will, so the oil will bring out more grain. Shellac will enhance the grain for sure, just not as much as a drying oil.

Stephen

Re: BLO under shellac Question

#10

Re: BLO under shellac Question

James Watriss

I've had success using shellac to french polish, almost immediately after applying the oil, provided the excess is removed. More specifically, I use a BLO and pumice paste for grain filling, followed by a heavy cut of shellac, and moving through lighter cuts to a high polish.

One of the traditional methods for french polishing with 'lac is to use raw linseed oil as a lubricant during the process of rubbing the finish out. So...

I guess waiting a day can't hurt.

Re: BLO under shellac Question

#11

Re: BLO under shellac Question

FredD

When I use a oil to enhance figured grain , I use Watco Danish oil or Satin oil, it has a couple of advantages over BLO , it is lighter , penetrates better and the resin in it hardens the wood.

And you can finish over it the next day every time.

FredD

Re: BLO under shellac Question

#12

Agree...

John in NM

Overnight is good out here when it's 90 degrees and 6% Relative humidity :D

Lower temperature seems to make more of a difference than RH, but I've never done a quantitative study of it.