Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

installing click laminate flooring

Posts

installing click laminate flooring

#1

installing click laminate flooring

Michael Dresdner

If you've installed click together laminate flooring, I could use some advice.

I just picked up some click together laminate flooring from IKEA and plan to install it in a rarely used spare bedroom. The floors (once carpeted) are plywood and seem level and smooth. Any tips on installation? Can I float the floor, or must it be glued down? If so, all of it or just key parts, and what adhesive? Does it need anything below the flooring, or can it sit directly on the plywood underlayment?

Thanks.

Re: installing click laminate flooring

#2

Re: installing click laminate flooring  *LINK*

matt overton

Mike,

Take a look at this video. this should be all that you need.


http://www.lowescreativeideas.com/idea-library/videos/HowTo_install_laminate_flooring_0808.aspx

Re: installing click laminate flooring

#3

Re: installing click laminate flooring

John Veerkamp

If the floor is above grade you can lay it directly on the ply sub floor. They also sell a thin "cushion" plastic underlayment that you can install, but it's not necessary. Make sure there are no nails popping up from the sub. Also be sure to leave 1/4" expansion around the perimeter. This can be covered with whatever base trim you wish.

Re: installing click laminate flooring

#4

Re: installing click laminate flooring

John Veerkamp

Most brands do not require glue.

Re: installing click laminate flooring

#5

Re: installing click laminate flooring

Galen Vetterick

You should follow the instructions that come with the brand and type of flooring you purchased. Don't put it directly on your plywood subfloor unless you want a very squeaky floor. They all float so either they have a preinstalled backing or you use the flooring underlayment polyethylene they sell to match the flooring. Use the wall gap they recomend because they are all not the same.

Generic video can give you some ideas but again follow what is right for your flooring.

I'm not a big fan of this type flooring cause it's just not the same as walking on wood. Most do not last any longer than cheap carpet and heavy funiture can damage it if you are not careful. But only my opinion!

Re: installing click laminate flooring

#6

Re: installing click laminate flooring

Nathan

You do not use any adhesive, either between the flooring and the subfloor, or between the floor panels themselves (before they came out with the "click" version, ordinary white PVA glue was used in the tongue-and-groove).

With the click flooring I installed, we found that sometimes the joint would click and other times not. So we were forced to slide the tongue into the groove from the end. This was over 8 years ago, though. I doubt you'll have the same problem.

Around here, laminate flooring is ordinarily installed on a concrete subfloor. First, a thin layer of foam goes down and then the laminate. That's all there is to it. Special pads to dampen footstep noise are sold, but they cost extra and are not required.

Re: installing click laminate flooring

#7

Re: installing click laminate flooring

Nathan

I'm not a big fan of this type flooring cause it's just not the same as walking on wood. Most do not last any longer than cheap carpet

Neither am I, but the price is right. This type of floor makes a disturbingly loud noise when anything is dropped on it. One thing to watch out for (in use, not installation), is water. The laminate is waterproof, of course, but under that is HDF which loves to absorb water and expand. When the floor is mopped, water can and does penetrate into the HDF at the joints. This is a big factor in how long it lasts.

If you don't mop obsessively, though, you should be fine if the floor is in a residence. The manufacturers give ratings on how tough the flooring is and what level of foot traffic it will withstand. The floor I installed 8 years ago is going strong. Although some damage is visible at the joints (laminate being forced upward by expansion of the HDF - one of our renters was an obsessive mopper), it isn't serious.

Re: installing click laminate flooring

#8

Re: installing click laminate flooring

Barry Irby

Michael, Laminate flooring is like shellac. There are at least two different types. Maybe many types, but what I am getting at is some f it is very water resistant and some of it not at all. I think Pergo is one of the water resistant ones and many of the cheap imitations are not. If you can, get an actual sample of what you intend to use and a piece of the top of the line stuff for comparison. Dopa two inch long piece into water and let it stay for a day or two or maybe a week or two. The good stuff will be pretty much unaffected and the cheap stuff will swell up and fall apart. This may not be a real issue for you in a rarely used room that is very unlikely to get wet, but as a Home Inspector I have seem many floors that failed or are failing due to exposure to water. On that topic, I have done expert witness testimony on houses that flooded. In one case the family was hyper sensitive to mold and had a house built with no carpet and all laminate to avoid mold. A plumbing fitting blew off and the place flooded. The flooring was floating on a layer of water and it would squish and squirt up through the joints when you walked on it. This particular flooring was not really damaged by the water, but they had a mold factory under it. Had to remove it, dry thoroughly and reinstall.

Someone mentioned the sounds it makes. One woman had about a thousand square feet of it installed and hated the noise it made when she walked on it with her high heels so much she had it removed in about three days.

I've seen a lot of the water sensitive type failing because the edges swell and turn up just enough to cause the face laminate to scuff off. Looks like crap after a while.

Beyond that, follow the directions. Don't glue it either to itself or the subfloor. Leave the relief space around the perimeter. Either use the foam backed type or the rolls of foam.

Not a lot of middle ground. You will either like it or hate it.

Re: installing click laminate flooring

#9

I've done four of them…

Rod Peterson�Ormond Beach, FL

Three were "click together" and the fourth was a glue down. Never again on the glue down. The adhesive was a nasty PL type and got on everything. Did a whole house (daughter's) with it, thus had some help. I'd have hated doing it alone.

The other three were one moderately expensive and two cheap. I don't particularly care for any of them, but when SWMBO says, "I want the floors covered"… The cheap ones definitely feel cheaper than the more expensive ones, and the surface is much more fragile.

Use the underlayment. It's cheap enough, and it'll provide just that much cushion to make the floors palatable.

I don't think it's possible to install the things without having to use some mechanical, sudden, inertial persuasion (hammer). Use scraps of the material to cushion the impact and protect the edges. Even doing so with the cheap stuff led to some damaged surface, so be careful.

Whether you start with a fresh saw blade or one that has some cuts on it, plan on resharpening after the job—the stuff is really tough on carbide. It might be worthwhile to buy an inexpensive big box blade for the job and then just toss it.

The biggest pain for me is undercutting the casings for door openings. I've used my biscuit joiner, but the cut is just a little too high, although workable. I have a "flip-over" offset handle dovetail saw that I use most of the time, but it's a knuckle buster.

You'll have to remove about half of your baseboard (and all of the shoe molding, if you have any). It'll become obvious why once you've started. When you finish, just reinstall the removed base, but when you install/reinstall the shoe molding, be sure to nail it to the base and not to the floor.

One word: knee pads. You'll spend a lot of time on them and you'll also be up and down a lot unless you have help to make the cuts. You can do the job alone, and a typical 13'×13' room can be done in a day, if you put in some time. I no longer enjoy putting in that much time, so I usually take two. Once the prep work is done, though, the field goes really quickly. All the rooms I did with the click type were bedrooms with closets, so cutting in those (and prep) almost doubled the time.

Rod