Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

where do you sign?

Posts

where do you sign?

#1

where do you sign?

DizD

I'm finishing a 9 drawer dresser for a friend of mine and plan to sign it when done. A lot of commercial pieces have logo in the top drawer, but writing here after construction would put it "upside down". I've seen some pieces signed on the back of a drawer or the back of the piece. Anyone have a favorite spot?

Re: where do you sign?

#2

Moses Yoder

Re: where do you sign?

Moses Yoder

I built a drawer cabinet for CD's once for a pastor that was retiring. Our sunday school class funded the cost of materals for it, and when it was done we all wrote something for him on the sides of all the drawers and signed it. It was kind of unconventionally neat when you opened the drawers, instead of just a plain drawer side they had grafiti all over them.

In the kitchen cabinet business we have an engraver and engrave a logo in the top left inside of the drawer, before it is assembled.

Re: where do you sign?

#3

Re: where do you sign?

PaulSV

I make a little 1 inch brass disc, about 1/8 inch thick, and engrave my initials and the year on it. I drill a 1 inch hole 1/8" deep with a forstner bit, and epoxy the brass disc into that. On a piece with drawers, I put it on the outside of one of the top drawer sides. On a table without drawers, I'll put it on the inside of a rail.

Re: where do you sign?

#4

Re: where do you sign?

John McGaw

On the very few pieces I've signed, all of them being gifts, I've signed in a location that can be seen only from the bottom. An example would be inside the base or skirt if the piece has such. I never got into the practice of signing turnings and have done no more than initial a few pieces at the bottom center.

Re: where do you sign?

#5

Re: where do you sign?

steve mackay

Sign on the back. Upper right hand corner (unless the piece sits "in the open"). But don't forget posterity. I always put a message/date/location inside on the back panel (or underside/inside of my models). The more cryptic the better. Give the future Antiques Roadshow something to ponder. :D

Re: where do you sign?

#6

Ellis Walentine

Couple ways

Ellis Walentine

On pieces that I designed and built myself, I inlaid a little ivory rosebud. On a table or a dresser, it would be on the top, near the front corner, or perhaps in the exact center of a table. On a chair it would be at the top center of the back splat or in the crest rail. On architectural pieces, it would be wherever seemed appropriate ... in the face of a newel post, in an intarsia inlay in a floor, etc. I think this signature needs to be very simple and understated or else it doesn't work.

When I was first starting out, in the early '70s, I used to make up a little card about the size of a business card and use a fine-tipped permanent ink pen to draw my insignia, with a description of the piece, the main materials used and the date. On a table, I would glue it to the underside of the top. On a dresser that was intended to stand against a wall, I would glue it to the back, usually at the bottom center.

Ellis

Re: where do you sign?

#7

Clint Searl

Re: where do you sign?

Clint Searl

Usually on the underside or interior with a card I compose with Photoshop. The graphics vary. Here's one from last year on a little bench.

Clint


Re: where do you sign?

#8

Re: where do you sign?

George Colonel's Workshop-Havertown PA

Good Afternoon Diz,

Drawer sides are usually the place. I do it after assembly by holding my branding iron upside down. I initial the branding and apply the month and year. For family, I always write a message in the back of the item. Pencil, then sprayed with shellac.

George

Re: where do you sign?

#9

Ellis Walentine

Finally...

Ellis Walentine

... a good use for computers.

Nice, Clint.

Ellis

Re: where do you sign?

#10

Kneale Brownson

Re: where do you sign?

Kneale Brownson

I've used a Penny for the date and a woodburner for the sig next to it.

Re: where do you sign?

#11

Re: where do you sign?

B. Loder

I burn my brand somewhere on the back of a project, usually, if it doesn't show there. But besides that, I've been putting the date, and whatever stain and finish I put on it, in case someone ever wants to know. I also put the brand of finish and stain, so it would match, if someone ever had to touch it up.