Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Nearly 100 Exotic Wood Species, Direct-Imported Since 1972. Shop Slabs & Turning Stock.

Rust on Tools

Posts

Rust on Tools

#1

Rust on Tools

Richard Krieger

Hi All:

Long time, no post. I live in Michigan where there are huge changes in climate, temperature and humidity. I am looking for ideas/suggestions on what has proven successful for a coating on steel and iron tools to prevent rusting. Specific examples are block planes, precision measurement tools, steel scales, bar-clamps, etc. I have tried WD-40 with some success, but often have to re-apply sooner than I think I should. My shop is stick-built with insulated walls and ceiling. Furnace and air-conditioning equipped, but not continuous. (only when I work out there).

What has proven to be a good solution for others out there?? Thanks in advance for any help anyone might render.

Re: Rust on Tools

#2

Re: Rust on Tools

FredD

Boe-Shield last longer then WD 40 , I have used Hoppe's gun oil with success when my tools were exposed daily working as a Carpenter and it is the least costly of the three.

FredD

Re: Rust on Tools

#3

JL

Re: Rust on Tools

JL

I usually clean with WD-40 or mineral spirits then wax.

I've used Renaissance Wax and paste wax as topping.

Re: Rust on Tools

#4

Steve Strickland

Re: Rust on Tools

Steve Strickland

Plain old Min-Wax is good. Probably any wax would work fine.

Re: Rust on Tools

#5

Re: Rust on Tools *LINK*

del schisler

get rust off than T-9 that is all that i use and i am in florida. I belive you can get this at sears now?


http://boeshield.com/

Re: Rust on Tools

#6

Johnson's paste.

steve mackay

Re: Rust on Tools

#7

Kneale Brownson

Rust in my N. MI barn

Kneale Brownson

I've use TopCote on all my saw/jointer/planer tables and on tools like C-clamps for years and years in my unheated, barely insulated barn in Traverse City, where everything will bubble with condensation occasionally as the weather changes quickly.

On the tabletops, it reduces resistance to sliding, but will wear off in a week or so under heavy use of the tool, requiring another quick spray. A $15 can (I started using it when it was less than $10 a can) used to last me a summer season or more on two table saws, a scroll saw, two jointers and a planer. Tools like C-clamps get a spray maybe once a year.

Re: Rust on Tools

#8

Re: Rust on Tools

Bob Entwisle in NJ

Plain old MinWax for me.

I tried T-9 and I don't think it lasts as long as a couple of coats of MinWax.

Bob in NJ

Re: Rust on Tools

#9

Re: Rust on Tools

Terry Quiram

A piece of 1/4 inch plywood to completly cover flat surfaces will keep them from rusting. My tools used to be in my uninsulated garage and that is how I controled rust. All other suggestions for non flat items are good. Just have to pick which one you want to use.

Re: Rust on Tools

#10

Another solution *LINK*

doug f, san clemente, ca

I've had pretty good luck with this stuff. I use it to wrap planes and chisels after they've been sharpened and it seems to stop the rust for quite some time.

I live in a coastal community that has high humidity and problems with salt water corrosion are rampant. This paper and a light coat of paste wax seem to keep the problem at bay.

Doug


Ferro-wrap

Re: Rust on Tools

#11

Re: Rust on Tools

pete labelle

You are aggrevating the situation by only intermittently running the AC. AC here in Michigan (Holland) is used partially to reduce the air temp, but also to de-humidify.

If you cool off the shop for your Saturday project, then switch it off, your tools are now cooler than the air outside air temperature, and, once re-exposed to the humid air, will condense the water out of the air like a cold can of beer.

Rust retardign materials will help, but keeping the air dryer will help. If your shop is very leaky, seal off all cracks & crevices to retard any air flow back into the shop. Possibly run a de-humidifier when your shop is vacant to help keep the humidity at bay.

Pete

Re: Rust on Tools

#12

Moses Yoder

Re: Wooden boxes

Moses Yoder

A coat of some type of wax, I use Johnsons , plywood on machine surfaces as Terry suggested, and wooden boxes for hand tools. I built some wooden wall cabinets with glass panel doors for a bunch of hand tools. I pulled out a hatchet yesterday after not using it for several years, zero rust. I built a nice tool box for my user tools, pretty air tight when shut, and don't see any rust on my tools. I did leave a block plane in a leather sheath once and found out that was a mistake. I guess the stuff used to tan the leather causes rust, plus the leather holds moisture in. Some people use leather scabbards for saws, but it should be brain tanned leather if I remember right to prevent rusting.

Re: Rust on Tools

#13

Re: Wooden boxes

Richard Krieger

Well, WoodCentral continues to be a valuable source of information. Thanks to all who have posted their ideas and suggestions. I will take all into consideration and try some new things that I haven't before.

Thanks again for your help.

RLK