Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

Questions for those spraying finish

Posts

Questions for those spraying finish

#1

Questions for those spraying finish

Barry Irby

I have an ancient spray gun. It has been sitting on the shelf for twenty five years. It was not as clean as it should have been when it was put away. (I moved and it got "lost" in the shuffle.) Is there any chance it will work properly if I clean it? I suspect it will need new O rings or what ever, but I don't know. Its a Sears cup gun with the cup below the nozzle.

Whats with the guns that have the cup on top? What's with HVLP? If I buy a new gun, what type would you buy for spraying lacquer and urethane? What would you expect to pay?

Re: Questions for those spraying finish

#2

how about bite sized pieces

Bill Tindall

You asked 5 questions in your post and one, HVLP, does not have a short answer. I'll wager you will get more useful answers if you break your post into smaller pieces.

Re: Questions for those spraying finish

#3

Re: Questions for those spraying finish

FredD

It depends on the amount you spray, how large the objects, deadlines and your budget.

Many find the HVLP fits their needs, pressure pots and cup guns are traditional , for myself and those who do large projects and time is a consideration, nothing but a Airless will do , in my view. A compound answer for a compound question . ;-))

FredD

Re: Questions for those spraying finish

#4

Re: Questions for those spraying finish

Stuart Johnson

I've got a Rockler HVLP that I'm having so-so results using. I do think it is the operator and now that I'm just about done with my project the finish is looking better but it has been a learning chore. The other day I had a small project and pulled out my $40+ Critter. It worked great and is much easier to use. I don't know about using it for large cabinet projects but I will certainly be trying it on some turnings.

Re: Questions for those spraying finish

#5

Re: Questions for those spraying finish

Gary Smyth

If what you have is a Sears gun chances are that it is the old Campbell Hausfeld black top, aluminum cup version. Campbell Hausfeld makes a repair kit with gaskets and "O" rings and it is under $20. You may want to consider that while pondering the HVLP, airless, and other alternatives. The compressor may be your determinimg factor of the direction you want to go. Try spraying water on cardboard with what you have and see if it is satisfactory. If not, you will have to do substantial research even after the opinions you get here.

Re: Questions for those spraying finish

#6

Clint Searl

Re: Questions for those spraying finish

Clint Searl

First, buy an IR two stage 5 HP 240v single phase compressor with an 80 Gal tank. Then regulate and at the end of the line pipe your shop with drops every 10'. Add a reel with 75' of 1/2" hose. It'll come in handy for keeping your bicycle tires and basketball inflated.

Next, get at least three gun setups, starting with a 1 gal pressure pot and its gun, plus a couple top feed gravity feeders for general and detail work.

Finally, buy a five gallon pail of solvent lacquer, an equal amount of reducer, some retarder, and an organic mask.

Shoot your latest project.

Clint

Re: Questions for those spraying finish

#7

Jim DeLaney, Austintown, Ohio

Re: Questions for those spraying finish

Jim DeLaney, Austintown, Ohio

Why such a small compressor, Clint? :D :D

Re: Questions for those spraying finish

#8

Re: Questions for those spraying finish

FredD

He forgot the Sanding Sealer too. :D :D :D :D

FredD

Re: Questions for those spraying finish

#9

Re: Small

Mark Mandell - Gone Round In Jersey

That way, the thing will put out enough air to run a set of those great Dynabride sanders so you can use a Kw/min of electricity while you sand a board.

And Clint, you left out the refrigerated air dryer! Tsk Tsk :D

Re: Questions for those spraying finish

#10

Re: Questions for those spraying finish *LINK*

Dave Paine

Barry,

I recommend disassembly and solvent to clear out all passages. Some are quite small and easily blocked up.

Grizzly has an assortment of spray guns. I have one like the H8222 "below" cup with swivel lock.

You did not mention if you gun is pressurized or not. Some guns have a valve which will pressurize the container, vs suction pulling out the liquid.

I think the pressurized is for thicker fluids.

The "on top" style seems to be popular with the LVLP/HVLP style. These are all gravity/suction feed, so need thinner material. Should work well with lacquer. Urethane may need to be thinned.

I purchased a small "on top" style from Grizzly for touch-up or small projects. I do not recall which model. Less surface area to clean up.


http://www.grizzly.com/products/searchresults.aspx?q=spray%20gun&new=1