Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

Box Joint Jig

Posts

Box Joint Jig

#1

Box Joint Jig

Tom Henderson, Gulf Breeze Fl

I am in the process of making a box joint jig and discovered that I have a 1/64th inch slop in my miter bar. Is that enough to mess up a quarter inch box joint in half inch stock nine inches wide? If so, what is the best quick fix?

Re: Box Joint Jig

#2

Re: Box Joint Jig

Bruce, a MN Galoot

I like box joints and have used them on a bunch of projects, from small boxes to a couch frame. They are tricky to set up.

I don't know a quick fix, but it most assuredly could mess up the joint over a 9" run, particularly if all the gaps line up on the same side. You could try peening a small dimple on the side of the bar to close up the gap.

Re: Box Joint Jig

#3

Re: Box Joint Jig *LINK*

Lee Schierer McKean, PA

Yes it may mess up your box joints. You can add a layer of UHMW tape (available from McMaster Carr) to the sides of your miter bar to take up the space. Clean the miter bar with lacquer thinner or alcohol before applying the tape. UHMW tape is a very tough slippery material. You can trim it with a razor blade. It will last a considerable time if applied properly and treated with some care. Fold the ends around the ends of the miter bar. I find it lasts longer if I slide the miter bar in from the table edge rather than try to set it down into the miter slot.

Lee


UHMW Tape

Re: Box Joint Jig

#4

Re: Box Joint Jig

George Colonel's Workshop-Havertown PA

Good Afternoon Tom

Most of my joints are box joints, done either on my table saw or omnijig. Most of the larger ones are done on the table saw. They turn out best when everything is dead on. Forget the adjustable miter if it is at all sloppy or inaccurate. Build your jig on runners which use the miter slots in the saw. I designed mine to use both miter slots. I replace the jig face and spacer bar when the project requires a new size size box joint and finger spacer. The corners of this chest and chest top were cut on my table saw.

George

Re: Box Joint Jig

#5

Re: Box Joint Jig

FredD

Nice Chest Colonel, yours too :D

FredD

Re: Box Joint Jig

#6

Re: Box Joint Jig

Keith Newton----Little Rock, Arkansas

I like to use my TS sled for this, with a sub-fence clamped to the front of the fack fence of the sled. It is far more accurate, and much easier to set up and use.

If you try to use your miter gage, always try to feed with all of your feed effort to the same side every time on all parts, but even doing that, it is tough, especially if you are using a dense wood.

Re: Box Joint Jig

#7

Re: Box Joint Jig

FredD

Tom ,I was so busy looking at the Colonels Chest that I forgot to answer your question .

Using a center punch make a couple of dimples at both ends and the middle of one edge of the miter bar.

That should be enough so that you needn't go to the other side.

If it turns out to snug , just take a pass over the dished out dimples with a file.

That is what I have done to nearly every miter bar I have owned , sooner or later.

FredD

Re: Box Joint Jig

#8

Re: Box Joint Jig

Tom Henderson, Gulf Breeze Fl

Thanks for the prompt and helpful suggestions. I have made one jig using only one runner, and it works ok. I may try to make one with double runners before I start cutting the stock.

With a whole bunch of luck, maybe the results will be nearly as good as that picture...

Re: Box Joint Jig

#9

Re: Box Joint Jig

Alan in Little Washington (NC)

Box joints rely on a perfect fit- it must literally be set to a few thousandths of an inch. Dimpling the bar and some of the other suggestions mentioned here should help. I use 3/8" X 3/4" cold rolled steel from my local metal supplier for runners on all my jigs.

Besides the bar, there are other common causes of bad box joints so make sure the guide pin width and space between the guide pin and the blade are precisely the same. Don't try to work backwards- start with the size of notch the blade is cutting, not what you think or it is supposed to be cutting, and work from there. Use direct sizing, try not to use calipers when sizing the guide pin and setting the gap.

All that being said, something new is just around the corner that solves all the problems of existing and homemade jigs.

Re: Box Joint Jig

#10

Kneale Brownson

How old is that pix???

Kneale Brownson

You look like you've trimmed down a bunch, George. Did you change beers?

Re: Box Joint Jig

#11

Re: Box Joint Jig

Henry Higginbotham

Alan, I was just about to write and ask you how that was coming. Keep us posted! ;)

Re: Box Joint Jig

#12

Re: Box Joint Jig

Alan in Little Washington (NC)

I will.