Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Price drop on over 1300 Rockler items

OT - split in a galvanize "Tee"

Posts

OT - split in a galvanize "Tee"

#1

JL

OT - split in a galvanize "Tee"

JL

Naturally swapping it out would be a MAJOR PITA. There are nipples on both sides and a valve in close proximity to the "Tee".

The person neglected to drain the "Tee" in the cold weather last winter. Now that it's getting hot, they would like the waterers up and functioning.

Any thoughts? As I said, it would be a big problem to swap out the "Tee" - but I'll do it if it necessary.

Re: OT - split in a galvanize "Tee"

#2

Re: OT - split in a galvanize "Tee"

Mark Mandell - Gone Round In Jersey

You'll need 2 unions, shorter nipples, a new tee, wrenches and a Sawsall. Where you put the unions depends on where your 1st right angle occurs in each branch. Your other options are to replumb in copper or put in a PEX manifold and home runs to each fixture. A good PEX clamp tool will run you about $350, but you'll use it more and more.

Re: OT - split in a galvanize "Tee"

#3

Re: OT - split in a galvanize "Tee"

Bill Howatt

You know as well as I do that replacing it is the proper repair. If it is outside and leaking due to a poor repair won't cause any damage other than annoyance I'd probably try epoxy or some of that "magic" stuff I've seen advertized on TV (can't remember the name).

I guess brazing might be an option if you have a good torch.

BIll

Re: OT - split in a galvanize "Tee"

#4

Re: OT - split in a galvanize "Tee"

FredD

Heat shrink tape is a fast temporary fix, it sounds like a thirty minute job for a Plumber, know one?

Have a air connection installed, so you can blow the system in the fall , only good way to rid it of water.

FredD

Re: OT - split in a galvanize "Tee"

#5

Clint Searl

Oakey plumbers' epoxy putty

Clint Searl

Five minute job -- that's how long it takes for the putty to harden. Trust me!

Clint

Re: OT - split in a galvanize "Tee"

#6

Re: OT - split in a galvanize "Tee"

Joseph Mulherin

I agree with Mark...do it right as he suggested with unions and nipples. And I am a retired pipefitter/plumber

Re: OT - split in a galvanize "Tee"

#7

Vote against brazing

Neal in San Jose

First, it would be difficult to get a used fitting clean enough to be successful.

Second, heating a galvanized part hot enough to braze would release some very nasty gasses. In an enclosed area like a crawl space (where I'm guessing this is located), it could be really bad news.

Re: OT - split in a galvanize "Tee"

#8

That's What I Get

Mark Mandell - Gone Round In Jersey

for marrying a Master Plumber's daughter. :D :D

Re: OT - split in a galvanize "Tee"

#9

Re: OT - split in a galvanize "Tee"

John Veerkamp

I've had fair success with JB Weld. Clean and rough up the surface. If possible put something like a hose clamp over the top for added pressure protection. or a couple of hose clamps securing a piece of metal over the JB Weld.

Re: OT - split in a galvanize "Tee"

#10

JL

Will try the Oatey.

JL