Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

Spindle Sander Cabinet

Posts

Spindle Sander Cabinet

#1

Spindle Sander Cabinet

Dale Penkala

I picked up this 3 drawer oak cabinet at a garage sale for $10.00. I just couldn't resist. I figured I could use it for a small movable bench in the shop with storage but when I looked at my oscilating spindle sander sitting on the floor I figured it would be perfect for it to sit on and I could move it around the shop where I wanted to use it.

I made a top and bottom & used formica to cover them to give it a finished off look. The bottom I used 2" grey rubber locking casters.

All in all I'm pretty happy with it with the exception of the height. If it was 4"-6" shorter it wouldn't hurt my feelings. But its still a useable setup.


Dale

Mid-Michigan

Re: Spindle Sander Cabinet

#2

Get a shorter spindle sander!

Neal in San Jose

Just kidding of course. That looks like an elegant solution. My spindle sander is always in the way on a bench, table saw, floor, wherever. I'll have to keep an eye out for a small cabinet like that.

Re: Spindle Sander Cabinet

#3

Or wear heels

Bill Houghton, Sebastopol, CA

just stay away from spike heels - too dangerous in the shop. Wedges or platform heels would be better.

Re: Spindle Sander Cabinet

#4

Kneale Brownson

Good height for sniffing your woods, eh?

Kneale Brownson

Re: Spindle Sander Cabinet

#5

Re: Good height for sniffing your woods, eh?

Dale Penkala

Ya I'm pretty happy with it. Plus it gets it off the floor and out of the way. I see a way to shorten it up about 3" if I want to go thru the trouble. Now I'm constantly on the look out for small or any cabinet for that matter that I can pick up cheap at a garage sale.

As far as saw dust goes, I'm totally impressed with how well the shop vac takes care of it! I don't get any up in my face.

Dale

Mid-Michigan

Re: Spindle Sander Cabinet

#6

Don't lower the sander,

Tom Pilsbury (Chicago)

raise yourself. Build a small platform from a few pieces of 2x4 and plywood.

Re: Spindle Sander Cabinet

#7

Re: Don't lower the sander,

Dale Penkala

Hi Tom

Ya I have a couple of them, and that did crossed my mind to use them. I built them for my bench mounted drill press for certain things, plus it helps my little guy see what dad is doing. :)

Thanks for the tip!

Dale

Mid-Michigan

Re: Spindle Sander Cabinet

#8

Re: Don't lower the sander,

David Yoho

I don't know how tall you are but if it feels comfortable to you then it's at the right height.

That setup looks to be about the same as mine that sits on top of my stationary work bench, which is just right for me. The fact that you can move it where and when you need to is nice.

Re: Spindle Sander Cabinet

#9

Cut the top drawer off the cabinet

Barry Irby

Before you do that, be sure the height bothers you.

I had an old base for a jointer I used to cobble together a base for my planer. Made the planer about two inches taller than the table on the bandsaw. I made a new roll around base for the planer that made the height match the bandsaw. It makes a great infeed or outfeed table. I can lay stuff on it and cut it on the bandsaw.

Nice score.

Re: Spindle Sander Cabinet

#10

Re: Don't lower the sander,

Dale Penkala

Hi Dave

Ya at this point I'm just going to use it for a while before I do anything to it. I have a couple of plateforms that I can use if need be. I'm 5'10" and even though its a bit on the high side it is still pretty comfortable.

Yes being able to move it around is a really nice feature of the setup.

If & when I get a planer setup I'm going to do something like this as well so I can move it in and out of the shop when I need to use it.

I have another room off my shop where I store things and I also keep my wood in there as well. I think it is going to be a machine storage room too!!! :D

Dale

Mid-Michgan

Re: Spindle Sander Cabinet

#11

Re: Cut the top drawer off the cabinet

Dale Penkala

Hello Barry

Thanks for the tip! Good idea for using the table as basically an extension table for your bandsaw. I bet that comes in handy when you need it!

Ya I'm going to use it for a while 1st before I do anything to it. Right now just having it up off the floor and being able to move it when need be is a big plus!

Dale

Mid-Michgan